ADVANCED WHOLE HOUSE FANS ® OWNER’S GUIDE SMART ATTIC FAN CONTROL SEE // H E A R // F E E L THE QUIETCOOL DIFFERENCE 1 QUIETCOOLSYSTEMS.
GENERAL SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. Read Instructions - All safety and operation instructions must be read. Retain Instructions - The safety and operating instructions should be kept for future reference. Heed Warnings - All warnings should be followed. Follow Instructions - All installation and operating instructions should be followed. Water – The QuietCool system should not be used near water.
STOP! READ ALL INSTRUCTIONS IN THIS GUIDE BEFORE INSTALLING YOUR QUIETCOOL SYSTEM Read this guide before proceeding! The manufacturer is NOT responsible for faulty installation or product damages caused through failure to fully read this guide BEFORE attempting installation. FCC Regulations This device complies with Part 15 of the FCC Rules.
2. INSTALLATION TOOLS YOU WILL NEED - Phillips screwdriver - Power-drill - Philips bit 2-1 Installing the Hub IMPORTANT: If you are installing the Hub onto an existing QuietCool fan, be sure to shut off the power before attempting installation. If you are installing the Hub onto a new fan, perform all installation steps before plugging in the fan. 1. Open up the thermostat on your attic fan. Unwire the power cord and remove the plastic connector.
7. 8. Set the dip switch positions inside the Hub as shown in the diagram below. Figure A Attach green ground wires to ground screw Set dip switches: 1 - ON 2 - OFF 3 - OFF Power-on the Hub. The Power LED indicator will be lit. ON POWER 9. 10. Press the Test button to make sure the fan works. The Test LED indicator will blink once every two seconds indicating 1-speed and the fan will be on. Press the Test button again and the fan should shut off and the LED will be off.
8. Power-on the Hub. The Power LED indicator will be lit. 9. Press the Test button to make sure the fan works. The Test LED indicator will blink twice every two seconds indicating 2-speed and the fan will be on high. Press the Test button again and the fan will switch to low speed. Press the Test button again and the fan should shut off and the LED will be off. 10. If the fan doesn’t operate as described in step 9, please check the dip switch postion. Three Speed Wiring (for AFG SMT-3.
2-3 Fan Hub LED Indicators Power Indicator • The Power LED indicator will always be lit when the Hub is connected to Power. • If this LED is not lit, check the power source Timer Indicator • The Timer LED indicator will light up as shown below: 1. 1 Hour: 1 Blink 2. 2 Hours: 2 Blinks 3. 4 Hours: 4 Blinks 4. 8 Hours: 8 Blinks POWER TIMER TEST PAIR 5. 12 Hours: 12 Blinks 6. Continuous On: Off Test Indicator • The Test LED indicator will light up as shown below when the Test button is pressed: 1.
3-2 Operating the QuietCool Smart Control App When you first connect to your QuietCool Smart Attic Fan Control, your attic fan will show up in the list of available fans in the app. A message indicates that setup is required. Press and hold the Pair button on the Hub until the LED indicator begins to blink. NOTE: You will need to initiate this Pairing process on each device you want to use to control your attic fan. Tap on the fan to start the setup process.
Once setup is complete, tap Done in the Fan Setup page. Now you can tap the fan on the home page. You will be taken to the Fan Control page. On the Fan Control page, you will see the current fan status, the current attic temperature, as well as the current attic humidity level. You also have the option to Activate Smart Mode or Activate Timer Mode. You can also go into the settings of the fan and adjust the settings that you setup in the first step.
3-3 Frequently Asked Questions What protocal does this control use? This control operates over Bluetooth to connect to your phone. Will my neighbor be able to control my fan if they have the same set up as me? No. In order to connect to your Smart Attic Fan Control Hub, you must first pair your device by using the Pair button on the Hub. What is the range? The range restriction between your phone and the attic fan is 50 ft.
ATTIC FAN SMART CONTROL LIMITED WARRANTY QC Manufacturing Inc. extends this warranty to the original purchaser of the following IT-AF-SMT - installed and used in a residence under normal conditions within the United States: A. One year coverage applies to the product. At our option we will repair or replace any part of the assembly should it fail to operate during the first year from the date of original purchase. B. This warranty does not cover any of the following: 1.
QuietCool is Proudly Designed and Built in California ADVANCED WHOLE HOUSE FANS 1-888-QUIETCOOL 26040 Ynez Rd., Temecula, CA 92591 ® // PH 951.325.6340 // QUIETCOOLSYSTEMS.
