Specification
W
W
W
A
A
A
L
L
L
K
K
K
M
M
M
A
A
A
K
K
K
E
E
E
R
R
R
®
®
®
F
F
F
O
O
O
R
R
R
M
M
M
S
S
S
P
P
P
R
R
R
O
O
O
D
D
D
U
U
U
C
C
C
T
T
T
N
N
N
O
O
O
.
.
.
6
6
6
9
9
9
2
2
2
1
1
1
PRODUCT USE
QUIKRETE
®
Walk Maker
®
Building Forms are reusable plastic molds
used for forming concrete for pathways and patios. Available in
Country Stone, Running Bond Brick, European Block and Basket
Weave Brick patterns.
SIZES
• QUIKRETE
®
Walk Maker
®
Building Forms are nominally 2’ x 2’ x 2”
(0.6 m x 0.6 m x 51 mm)
INSTALLATION
SURFACE PREPARATION
The Walk Maker
®
can be placed on any relatively flat surface. It will
automatically configure the concrete to the existing base. For
professional results, remove one inch of topsoil, and level Walk
Maker
®
before filling with concrete. Removed topsoil can be utilized
to fill in open spaces on sides and between concrete after walk has
set up.
MIXING
Add 2.5 quarts (2.4 L) of water to each 80-lb. (36.3 kg) bag or 2
quarts (1.9 L)of water to each 60-lb. (27.2 kg) bag of QUIKRETE
®
Concrete or Crack Resistant Concrete Mix. Mix thoroughly until a
plastic-like (moldable) consistency is reached. If additional water is
required, add small amounts until the correct consistency is obtained.
The final water content should be 2.5-4.5 qts. (2.4 – 4.3 L)for each 80
lb. (36.3 kg) bag, or 2-3.5 qts. (1.9 – 3.3 L) for each 60 lb. (27.2 kg)
bag.
APPLICATION
Use a bucket or trowel to fill each mold cavity level with surface of
mold. While concrete is still in mold, pat and smooth cavity surface
with trowel. Remove mold promptly. After removing the mold, smooth
all edges with a trowel until appearance is satisfactory. Dipping trowel
in water may be helpful. Place the mold adjacent to the completed
section and continue this process until your project is completed.
CURING
Concrete should be damp-cured for 5-7 days for the greatest strength
or QUIKRETE
®
Acrylic Concrete Cure & Seal – Satin Finish #8730
can be applied once the concrete hardens, but is
still damp. (Apply according to directions on the package). To
outline/trim blocks, fill-in separations with QUIKRETE
®
Sand/Topping
Mix after concrete has cured. Place dry Sand Mix in cracks and
sweep in to desired level. Dampen the Sand Mix with a fine mist of
water (do not over-wet). Let Sand/Topping Mix harden to finish the
project.
Note: The addition of QUIKRETE
®
Liquid Cement Color will
dramatically enhance any Walk Maker
®
project. Mix the liquid color
with water before adding it to the dry concrete mix. A variety of
surface textures may be obtained by experimenting with different
finishing techniques; i.e. a metal trowel will make a smooth surface, a
wooden trowel will make a rougher surface and a brushed surface will
add texture and expose more aggregate.
WARRANTY
The QUIKRETE
®
Companies warrant this product to be of
merchantable quality when used or applied in accordance with the
instructions herein. The product is not warranted as suitable for any
purpose or use other than the general purpose for which it is
intended. Liability under this warranty is limited to the replacement of
its product (as purchased) found to be defective, or at the shipping
companies’ option, to refund the purchase price. In the event of a
claim under this warranty, notice must be given to The QUIKRETE
®
Companies in writing. This limited warranty is issued and accepted in
lieu of all other express warranties and expressly excludes liability for
consequential damages.
The QUIKRETE
®
Companies
One Securities Centre
3490 Piedmont Rd., NE, Suite 1300, Atlanta, GA 30305
(404) 634-9100 • Fax: (404) 842-1425
PRODUCT DESCRIPTION
QUIKRETE
®
Walk Maker
®
Building Forms are reusable plastic molds for creating
p
atterned walks
,
p
aths
,
p
atios
,
court
y
ards
,
etc.
Maintenance of Concrete
03 01 00
DIVISION 3
* Refer to www.quikrete.com for the most current technical data, MSDS, and guide specifications