Installation Guide

A
A
A
D
D
D
V
V
V
A
A
A
N
N
N
C
C
C
E
E
E
D
D
D
P
P
P
O
O
O
L
L
L
Y
Y
Y
M
M
M
E
E
E
R
R
R
M
M
M
O
O
O
R
R
R
T
T
T
A
A
A
R
R
R
J
J
J
O
O
O
I
I
I
N
N
N
T
T
T
S
S
S
E
E
E
A
A
A
L
L
L
A
A
A
N
N
N
T
T
T
P
P
P
R
R
R
O
O
O
D
D
D
U
U
U
C
C
C
T
T
T
N
N
N
O
O
O
.
.
.
8
8
8
6
6
6
2
2
2
0
0
0
-
-
-
1
1
1
8
8
8
PRODUCT USE
QUIKRETE

Advanced Polymer Mortar Joint Sealant is a non-shrink
weather-resistant, high performance advanced polymer sealant
formulated to fill cracks and joints in mortar, in interior or exterior
areas up to 1 inch (25.4 mm) in width. QUIKRETE
®
Advanced
Polymer Mortar Joint Sealant is UV resistant and adheres to concrete,
brick, masonry, wood, glass, vinyl, and most plastics. QUIKRETE
®
Advanced Polymer Mortar Joint Sealant is ready-to-use and cures
upon contact with the moisture in the air to form a durable flexible
seal.
QUIKRETE
®
Advanced Polymer Mortar Joint Sealant may be used
for:
Sealing & Waterproofing horizontal or vertical control joints or
expansion joints in sidewalks, driveways, industrial floors, parking
decks, etc.
Environmentally friendly – solvent & isocyanate-free
SIZES
QUIKRETE

Advanced Polymer Mortar Joint Sealant is available in
gray 10 oz (295 mL) tubes.
YIELD
10 oz (295 mL) tube will fill approximately 13 linear feet (3.9 m) in 3/8
in (9.5 mm) wide bead .
TECHNICAL DATA
QUIKRETE

Advanced Polymer Mortar Joint Sealant meets
performance requirements of ASTM C 920, Type S, Grade NS, Class
25, Use T, NT, A, G, and M; Federal Specification TT-S-0230C, Type
II, Class A; CSA CAN/CGSB 19.13-M87. Meets VOC requirements in
all regions.
QUIKRETE

Advanced Polymer Mortar Joint Sealant, when tested in
accordance with standard procedures, provides typical results as
listed in Table 1.
TABLE 1 TYPICAL PHYSICAL PROPERTIES
Tack-Free Time at 77°F (25°C), 50%
RH
60 minutes
Cure Rate at 77°F (25°C) , 50% RH
¼ in (6.3 mm) at 24 hours
Dynamic Joint Movement
+/- 25%
Durometer Hardness, Shore A
35 to 45
Ultimate Tensile Strength
225 psi (1.5 MPa)
Elongation
250 to 350%
INSTALLATION
NOTE: It is recommended that impervious gloves – such as nitrile be
worn during application. QUIKRETE
®
Advanced Polymer Mortar
Joint Sealant is difficult to remove from skin and clothing. If sealant
gets on skin, immediately wipe off with a dry cloth. Use only in well-
ventilated, exterior areas. Before handling read Safety Data Sheet at
www.quikrete.com.
APPLICATION
SURFACE PREPARATION
The key to long-term sealant performance is proper substrate
preparation. The substrate must be clean, frost free, sound and free
of any oils, greases, or incompatible sealers, paints or coatings that
may interfere with adhesion and good joint performance.
Porous surfaces should be cleaned of dirt, dust, loose debris and
other potential bond breakers. Mechanical methods, such as wire
brushes, grinders, etc. may be required to remove surface
PRODUCT DESCRIPTION
QUIKRETE

Advanced Polymer Mortar Joint Sealant is a
superior, textured, one-component, permanently flexible,
multipurpose sealant.
DIVISION 7
2
Joint Sealant
07 92 00