Installation Guide

A
A
A
D
D
D
V
V
V
A
A
A
N
N
N
C
C
C
E
E
E
D
D
D
P
P
P
O
O
O
L
L
L
Y
Y
Y
M
M
M
E
E
E
R
R
R
N
N
N
O
O
O
N
N
N
-
-
-
S
S
S
A
A
A
G
G
G
S
S
S
E
E
E
A
A
A
L
L
L
A
A
A
N
N
N
T
T
T
P
P
P
R
R
R
O
O
O
D
D
D
U
U
U
C
C
C
T
T
T
N
N
N
O
O
O
.
.
.
8
8
8
6
6
6
6
6
6
0
0
0
-
-
-
1
1
1
1
1
1
PRODUCT USE
QUIKRETE

Advanced Polymer Non-Sag Sealant is a non-shrink
weather-resistant, high performance advanced polymer sealant
formulated to fill cracks and joints in concrete, in interior or exterior
areas up to 1 inch (25.4 mm) in width. QUIKRETE
®
Advanced
Polymer Non-Sag Sealant is UV resistant, adheres to concrete, brick,
masonry, wood, glass, vinyl, and most plastics and is compatible with
SBS flashing. QUIKRETE
®
Advanced Polymer Non-Sag Sealant is
ready-to-use and cures upon contact with the moisture in the air to
form a durable flexible seal.
QUIKRETE
®
Advanced Polymer Non-Sag Sealant may be used for:
Sealing & Waterproofing horizontal or vertical control joints or
expansion joints in sidewalks, driveways, industrial floors, parking
decks, etc.
 Caulking around window or door openings
 Sealing skylights and chimney flashings
 Environmentally friendly – solvent & isocyanate-free
SIZES
QUIKRETE

Advanced Polymer Non-Sag Sealant is available in gray
10 oz (295 mL) tubes.
YIELD
10 oz (295 mL) tube will fill approximately 12 linear feet (3.6 m) in 1/2
in (13 mm) wide by 1/4 in (6.3 mm) deep joint .
TECHNICAL DATA
QUIKRETE

Advanced Polymer Non-Sag Sealant meets
performance requirements of ASTM C 920, Type S, Grade NS, Class
25, Use NT, A, G, and M; TT-S-0230C, Type II, Class A; CSA
CAN/CGSB 19.13-M87. Meets VOC requirements in all regions.
QUIKRETE

Advanced Polymer Non-Sag Sealant, when tested in
accordance with standard procedures, provides typical results as
listed in Table 1.
TABLE 1 TYPICAL PHYSICAL PROPERTIES
Tack-Free Time at 77°F (25°C), 50%
RH
60 minutes
Cure Rate at 77°F (25°C) , 50% RH
¼ in (6.3 mm) at 24 hours
Dynamic Joint Movement
+/- 25%
Durometer Hardness, Shore A
30 to 40
Ultimate Tensile Strength
205 psi (1.4 MPa)
Elongation
350% to 450%
INSTALLATION
NOTE: It is recommended that impervious gloves – such as nitrile be
worn during application. QUIKRETE
®
Advanced Polymer Non-Sag
Sealant is difficult to remove from skin and clothing. If sealant gets on
skin, immediately wipe off with a dry cloth. Use only in well-
ventilated, exterior areas. Before handling read Safety Data Sheet at
www.quikrete.com.
APPLICATION
SURFACE PREPARATION
The key to long-term sealant performance is proper substrate
preparation. The substrate must be clean, frost free, sound and free
of any oils, greases, or incompatible sealers, paints or coatings that
may interfere with adhesion and good joint performance.
Porous surfaces should be cleaned of dirt, dust loose debris and
other potential bond breakers. Mechanical methods, such as wire
brushes, grinders, etc. may be required to remove surface
contamination, debris and failed sealants such as in re-caulking
PRODUCT DESCRIPTION
QUIKRETE

Advanced Polymer Non-Sag Sealant is a
superior, one-component, permanently flexible, multipurpose
sealant for vertical and overhead use.
DIVISION 7
2
Joint Sealant
07 92 00