Instructions

ManualsBrandsQUIO ManualsChip & Card TechnologyChip card reader

Standalone Access Controller and Reader QU-M2

Description& Features：

.1 Description:

QU-M2 is a waterproof standalone access control, reading EM&HID card, it uses advanced Microprocessor, with high-capacity flash memory for

0000 users. Users can be added and deleted via admin card, very simple to operate. The infrared remote control make the device not only have alarm,

protection, two units interlocked, anti-passback function but also can make two units interlocked, add and delete the user on the remote control key

directly.

Besides, it has low power consumption design, anti-theft alarm, door release button ect. , all these make it convenient, safe and reliable.

Features:

Feature

Description

Rainproof, moistureproof , durable

Longer working life, more stable performance

10000 card users

Waterproof Design

Ultralow power consumption

Large capacity

wiegand reader

Can used as wiegand 26 output reader

Can connect EM/IC/HIDwiegand 26 output reader

two units can be interlocked online

Single door or two doors anti-passback

Connect external reader

two units interlocked

Anti-passback

Installation, wiring, diagram

.1 Installation：

.1.1 Drill the holes according to the distance and the dimension on the back cover, or install the distributing box.

.1.2 Thread the cable through the cable hole, connect wires needed, wrapped Unused wires with insulating tape in case of short circuit

.1.3 Fix the back cover on the wall with special screw

.1.4 Fix the front cover to the back cover with the screws

.2 Wiring

No.

Marks

RESET

GND

Color

Pink

Description

RESET

Pink

RESET

Green

White

Gray

Wiegand output D0

Wiegand output D1

Alarm

ALARM-

OPEN

D_IN

+12V

Yellow

Brown

Red

Exit button

Door contact switch

+12V Input

Summary of content (6 pages)

PAGE 1
Standalone Access Controller and Reader QU-M2 Description& Features： 1 1.1 Description: QU-M2 is a waterproof standalone access control, reading EM&HID card, it uses advanced Microprocessor, with high-capacity flash memory for 10000 users. Users can be added and deleted via admin card, very simple to operate.
PAGE 2
9 GND Black GND 10 NO Blue Relay NO end 11 COM Purple Relay Com 12 NC Orange Relay NC end Note：Please check all wires and install front cover carefully before power on. 2.
PAGE 3
Factory Reset and Set management card Connect the two pink wires，then power on. After the sound“didi”, Factory reset is finished. When indication LED turns green，it means you can set two admin cards now，read the first card as admin add card，the second card as admin delete card，then LED turns red flash，after this, this device can work ,resetting to factory default.
PAGE 4
Entering admin operating mode: Press * Master code # factory default:999999 Note：All the below operations need be under programming mode. 4.1 Change the master code： Press 0 new code # repeat new master code# Note: Master Code length:6~8 digits 4.2 Add users by remote control： 4.2.1 Read card to add user： Press 1 read card # read card ... # 4.2.2 Use ID Number to add user： Press 1 card number # ... card number# ... # Note: 1.
PAGE 5
4.8 4.8.1 Interlock setting： Close interlock（factory default）： press 4.8.2 7 0 # 。 # 。 Open interlock： press 7 1 4.9 Anti-passback mode setting： 4.9.1 Disable anti-passback（factory default）： press 4.9.2 8 0 # 。 Enable anti-passback host mode： press 8 1 # 。 4.9.3 Enable anti-passback subsidiary mode： Press 8 2 # 。 Note：Details will be illustrated in Advanced Application below. 5 Admin card operation： 5.1 Add user： Press 5.
PAGE 6
10 Lock Output Load 2A Alarm Output Load 2A management card 2pcs Packing List Name Access Control Model/Spec QU-M2 Infared Remote Control 1 1 Manager Add Card 1 Manager Delete Card Manual Quantity 1 QU-M2 1 Self tapping screws Φ3.