Programming Command Guide （Version 1.
Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual. The device must be set to an TTL-RS232 interface. The following commands can be sent via a PC COM port using terminal emulation software.
Example: “Set the unit default” (HEX): Send: 02 f0 03 30 44 30 31 30 30 2e Hex value of Menu number 0D0100 Hex value of Character “.” Response: 30 44 30 31 30 30 06 2e Message example: Set the unit default: Send Commands(HEX): 02 F0 03 30 30 44 30 31 30 30 2e Response(HEX): 30 30 44 30 31 30 30 05 2E equal to ( \x02\xF0\x030D0100.
4 Menu number Function Details Menu Number Setting Value Restore All Factory Defaults Activate Defaults 0D0100 Interface 232 Interface 091804 232 Interface Baud rate 3 4800 BPS 4 9600 BPS 5 19200 BPS 060702 7 57600 BPS 8 115200 BPS(default) 9 2 060703 091809 060D02 1 2 USB COM Port Emulation 060500 130 Trigger Mode(default) 091A00 NA Presentation Mode 090901 NA Trigger Mode with cell phone reading 091B00 NA Presentation Mode with cell phone reading 090902 NA 0 Off(d
High Level Illumination (default) Mid Level Illumination 1 Illumination for Presentation Mode in Mid Level Illumination 2 Scanning Low Level Illumination 0 1 040100 3 Illumination OFF 4 High Level Illumination 0 Mid Level Illumination 1 Illumination for Presentation Mode in Mid Level Illumination 2 Idle Low Level Illumination (default) 040101 On (default) Off Low Beeper Tone – Good Read Beeper Duration – Good Read 3 4 050210 05021D Middle High (default) Normal (default) 050216 Barcode Sc
Save Not Save Enable/Disable All Symbologies Save setting 0D0400 NA Not save setting 0D0500 NA Enable All Symbologies Disable All Symbologies Restore the Factory Defaults of Code 128 (default) Enable Code 128 (default) Code 128 Disable Code 128 020100 020A00 020A01 1 0 Min~90 Code 128 min length 020A02 0~max Restore the Factory Defaults of EAN-8 (default) 021400 NA Transmit EAN-8 Check Digit (default) 021401 021402 Do Not Transmit EAN-8 Check Digit Enable 2-Digit Add-On Code 021403 021
EAN-13 Add-On Code Not Required (default) Enable ENA/JAN-13 Addenda Separator (default) Disable ENA/JAN-13 Addenda Separator Enable ISBN Translate Disable ISBN Translate (default) Restore the Factory Defaults of UPC-E (default) Enable UPC-E0 (default) 0 021306 021307 021200 021201 Disable UPC-E0 Enable UPC-E1(default) Disable UPC-E1 Enable UPC-E0 Check Digit (default) 021202 021204 Enable UPC-E0 Required 021203 021208 021209 021205 Disable 5 Digit Addenda (default) Restore the Factory Defaults of
Disable UPC-A Separator Enable UPC-A Number System (default) Disable UPC-A Number System Enable 2 Digit Addenda 0 021103 021104 Disable 2 Digit Addenda (default) Enable 5 Digit Addenda Disable 5 Digit (default) Restore the Factory Defaults of Interleaved 2 of 5 (default) Enable Industrial 2 of 5 Interleaved 2 of 5 021105 020400 020401 1 0 NA 1 0 No check Char (default) 0 020402 2 1 Interleaved 2 of 5 max length 020404 Min~80 Interleaved 2 of 5 min length 020403 2~max Restore the Factory De
Validate and Transmit 2 Validate no Transmit 1 Enable Code 39 Full ASCII Disable Code 39 Full ASCII (default) Min~48 Code 39 min length 020307 0~max Restore the Factory Defaults of Coda bar (default) 020200 NA 020201 0 020206 Min~60 Coda bar min length 020205 2~max Transmit Start/Stop Character 020202 No Check Char (default) Validate and Transmit Restore the Factory Defaults of Code 93 (default) Enable Code 93 1 0 0 020203 Validate no Transmit 2 1 020D00 020D01 Disable Code 93
Validate Type 10, Transmit 1 Validate 2 Type 10 Characters, No Transmit 2 Validate 2 Type 10 Characters, Transmit 3 Validate Type 11 Then Type 10 Character, No Transmit 4 Validate Type 11 Then Type 10 Characters, Transmit 5 Disable MSI Check Characters 6 Restore the Factory Defaults of PDF 417 (default) Enable PDF 417 (default) PDF 417 Data Matrix 1 0 021F06 Min~2750 PDF417 min length 021F05 1~max Restore the Factory Defaults of Micro PDF 417 (default) 022000 022001 Disable Micro P
Restore the Factory Defaults of Aztec (default) Enable Aztec Aztec 023301 Disable Aztec (default) China Postal Code 023306 Min~3832 Aztec min length 023305 0~Max Restore the Factory Defaults of Hanxin (default) 023800 NA 023801 Disable Hanxin (default) 1 0 Hanxin max length 023803 Min~7833 Hanxin min length 023802 1~max Restore the Factory Defaults of China Postal Code (default) 021800 1) Serial Enable China Postal Code Restore the Factory Defaults of Telepen (default) Enable Telepe
