Installation Guide

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
BulbRecommended:
EstimatedAssemblyTime:
Preparation:
(6)CandelabraBase60WMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer service for replacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-ABN5006RK
For Style ABN5006RK
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
A
Hardware Contents
Center
Column
x1
AA
BB
CC
DD
EE
FF
II
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
Canopy Lock
Ring
x1
Ceiling
Canopy
x1
GG
Fixture Chain
x1
HH
Quick Link
x2
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
of the Nipple (DD) and
thread the Canopy Chain
Loop (EE) onto the Nipple
(DD). By using pliers,
thread the Hex Nut (CC)
against the Canopy Chain
Loop (EE) and hand
tighten until snug.
B. Thread another Hex Nut
(CC) to the middle of the
Nipple (DD). Place
another Lock Washer (BB)
over the Nipple (DD) and
then thread the Nipple
(DD) into the Crossbar
(AA) until the Nipple (DD)
is about 0.375” above the
Crossbar (AA).
C. Remove the Canopy Lock
Ring (FF) from the Canopy
Chain Loop (EE). Place
August2014
AA
BB
CC
Step B
Step A
DD
CC
BB
EE
II
FF
B
Fixture
Body
x1
STEP 2 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end
Green Ground
Screw
STEP 3 Install Column to Fixture Body-
A. Unfold support arms on fixture assembly
to proper locations.
B. Thread Center Column (A) onto Fixture
Body (B), tighten until sung.
Figure 3
A
B
the Ceiling Canopy (II) over the Canopy Chain Loop (EE) against
the ceiling to determine the correct position of the Nipple (DD).
Thread the Canopy Lock Ring onto the Canopy Chain Loop (EE).
Adjust the Nipple (DD) to allow the Ceiling Canopy (II) to rest
against the ceiling when held in place by the Canopy Lock Ring
(FF).
D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).
Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in
place.
Figure 2