Installation Guide
1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Assembly Instruction Sheet #IS-ADE1716ER
For Style ADE1716ER
Pleasegoto forproduct cleaningtips. Goto the selection.
(3)Medium Base60W bulbMaximum,Alternatebulb (3)13W CFLMaximum.
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
www.quoizel.com Care+ Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape, safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
A
Crossbar
Assembly
x1
B
Ceiling Canopy
x1
H
Stem with
Hex Nut
x1
F
Shade Assembly
x1
STEP 1 Install Ceiling Canopy,
Tube and Shade Assembly
-
A. Thread one end of the Tube (C)
onto the top center of the Shade
Assembly (F) and hand tighten
until snug.
B. Thread the Ceiling Canopy (B)
onto the top end of the Tube (C)
and hand tighten until snug.
(Step 3 Continued)
ceiling and the mounting balls.
If not, adjust the length of the
mounting screw on the
Crossbar Assembly (A) by
unscrewing the preassembled
hex nut and lock washer and
Figure 1
I
Finial
x1
G
Diffuser
x1
D
Washer
x1
Hex Nut
x1
E
C
Tube
x1
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the
Crossbar Assembly (A). Attach the
Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw
facing you. Secure it with Outlet Box
Screws (not included). Tighten until snug.
A
Figure 2
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
F
C
B
STEP 3 Fit Ceiling Canopy to Crossbar Assembly-
A.
eiling anopy to the
eiling canopy
Remove mounting balls from the Crossbar Assembly (A). Fit the
C C (B) Crossbar Assembly (A) and secure with
mounting balls. Note: The c should be snug against the
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
B
Figure 3
then screwing the
mounting screws in or
out of the crossbar until
the correct length is
achieved. Once the
ceiling canopy is
secure, remove the
mounting ball and
ceiling canopy and
proceed to Step 4.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
Mounting
Screw
Mounting Ball
A
B
Figure 5
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the outlet
box and position the Ceiling Canopy
(B) over the outlet box. Align the
holes in the Ceiling Canopy (B) with
the mounting screws, then attach the
Ceiling Canopy (B) using the
previously removed
mounting balls. Hand
tighten until snug.
December2015