Installation Guide

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
ElectricalInformation:
EstimatedAssemblyTime:
Preparation:
TotalWatts:21W;Lumens:749LM;ColorTemperature: 3000K; CRI (color rendering index):80; Driver: N/A, Driver
Replaceable:N/A;LEDModuleReplaceable:No;LEDDimmable:Yes.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer service for replacement
parts.
Warnings and Cautions
1of1
Assembly Instruction Sheet #IS-ALT8407WT
For Styles ALT8407WT
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
August2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
ALT8407WT
FINISH: WESTERN BRONZE
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
NO.
1
REQ.
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires between Inner Backplate (A) and Fixture Body (C).
Package Contents
B
Mounting
Screw
x4
Inner
Backplate
x1
STEP 1 Install Inner Backplate and
Fixture Body
-
A. Pass the supply wires through Inner
Backplate (A). Attach Inner Backplate (A)
to Outlet Box with the head of Green
Ground Screw facing you. Secure it with
Outlet Box Screws (not included). Tighten
until snug
B. Race all supply wires through the Inner
Backplate (A) as shown. Refer to Step 2
for wiring connections.
C. Attach Fixture Body (C) over Inner
Backplate (A) and secure with Lock Screws
(B). Tighten until snug with screwdrivers.
.
A
A
Figure 1
Outlet
Box
Outlet Box
Screw
C
B
C
Fixture
Body
x1
Figure 4
STEP 4 - Apply Silicone Sealer
A. Make sure exterior wall surface and
fixture backplate are free of dirt
before applying caulk. Using exterior
grade caulk, caulk over top of
backplate and down other side. Do
not caulk bottom of fixture backplate
to ensure proper moisture drainage.
Your fixture is now assembled and
ready to use. Enjoy!
Exterior
Grade
Caulk
Backplate
G3962SH SHADE
1
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
STEP 3 Install Shade to Fixture Body-
A. place one Rubber Washer (E) over the Bolt on the Fixture Body (C),
have no hole end of Shade (D) into the Cap on the Fixture Body (C),
the hole on the Shade (D) and other Rubber Washer (E) over the Bolt
as shown, secure by threading Lock Ball (F) onto the bolt, tighten
until sung.
Figure 3
D
Shade
x1
E
Rubber
Washer
x2
F
Lock
Ball
x1
C
Bolt
Cap
5”
7”
20”
11.5”
3”
8.5”
7”
D
E
F
1