Installation Guide

ManualsBrandsQuoizel ManualsChandeliersAME5018IB

Warnings and Cautions

1of2

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2014 QuoizelInc.

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Package Contents

Hardware Contents

Shade

x18

Crossbar

Lock Washer

Hex Nut

Nipple

Canopy Chain

Loop x 1

Canopy Lock

Ring x 1

Ceiling Canopy

Fixture Chain

Quick Link

Tuck Washer

Mounting Screw

STEP 1 Install Crossbar and Ceiling Canopy-

* Pliers is required for this step.

Drill a 5/8” diameter clearance hole on the top inside center of the

Oulet Box and through the Structural Support Member. Place

Crossbar (AA) onto Outlet Box and line up mounting holes with a set

of holes on Crossbar (AA). Thread Outlet Box Screws (not supplied)

into the mounting holes on the Outlet Box and tighten until snug to

secure the Crossbar (AA). By using a screwdriver, thread Mounting

Screws (KK) into the Structural or Bridging Member and tighten until

snug.

B. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end

of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the

Nipple (DD). By using pliers, thread the Hex Nut (CC) against the

Canopy Chain Loop (EE) and hand tighten until snug.

C. Thread another Hex Nut (CC) to the middle of the Nipple (DD).

Place another Lock Washer (BB) over the Nipple (DD) and then

ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers,wire cutters, wirestrippers, electricaltape,safety glasses.

BulbRecommended:

EstimatedAssemblyTime:

Preparation:

(18)Candelabra Base60W Maximum

30-45minutes

Identifyand inspectall parts beforebeginning installation.Check package contentlist anddiagramsbelow tobe sureallparts are

present.If anyparts are missingor damaged,do not attemptto assemble,install,or operatethe fixture. Contactcustomer servicefor replacement

parts.

Assembly Instruction Sheet #IS-AME5018IB

For Style AME5018IB

thread the Nipple (DD) into the

Crossbar (AA) until the Nipple (DD)

is about 0.375” above the Crossbar

(AA).

D. Remove the Canopy Lock Ring (FF)

from the Canopy Chain Loop (EE).

Place the Ceiling Canopy (II) over

the Canopy Chain Loop (EE)

against the ceiling to determine the

correct position of the Nipple (DD).

Thread the Canopy Lock Ring (FF)

onto the Canopy Chain Loop (EE).

Adjust the Nipple (DD) to allow the

Ceiling Canopy (II) to rest against

the ceiling when held in place by the

Canopy Lock Ring (FF).

D. Remove the Canopy Lock Ring (FF)

and the Ceiling Canopy (II). Tighten

the Hex Nut (CC) against the

Crossbar (AA) to secure in place.

Structural or

Bridging Member

Drill a 5/8”

Dia. Hole

Outlet Box

Screw (not

Supplied)

Figure 1

Socket

Assembly

Side Arm A

Side Arm B

STEP 2 Attach Side Arms-

A. Attach Side Arms A (B) to the Hooks

on the upper tier and attach Side

Arms B (C) to the Hooks on the

second tier as shown.

Figure 2

Hook

Upper

Tier

Second

Tier

STEP 3 - Install Fixture Chain, Safety Cable and Ceiling Canopy

A. Adjust Fixture Chain (GG) to your desired length by removing the

links if needed.

Pliers is required for this step.

B. With Fixture Chain (GG) not attached to Fixture Loop (A) and

Canopy Chain Loop (EE), pull supply wires and safety cable

through Fixture Chain (GG) alternating links. After wires and safety

cable are through Fixture Chain (GG), pull Supply Wires, Ground

Wire and safety cable through Canopy Lock Ring (FF) and Ceiling

Canopy (II) in order.

C. Attach one end of Fixture Chain (GG) to Fixture Loop (A) with one

September2014

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-AME5018IB For Style AME5018IB Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Bulb Recommended: (18) Candelabra Base 60W Maximum Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
Quick Link (HH). Lift fixture and Fixture Chain (GG) up and attach other end of Fixture Chain (GG) onto Canopy Chain Loop (EE) with another Quick Link (HH). The fixture will now hang safely. Close chain loop at Ceiling Canopy Loop (EE). Supply Wires D. Feed Supply Wires, Ground and Ground Wire and Safety Cable Wire through Canopy Chain Loop (EE) and Nipple (DD) into GG Outlet Box. Cut wires leaving approximately 8” of wire extending from the Outlet Box. E. Refer to Step 4 for safety cable installation. F.