Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.
(5)A19MediumBasebulbs100WMaximum,Alternatebulbs(5)23WCFL.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-AML5005OZ
For Style AML5005OZ
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Hardware Contents
AA
BB
CC
DD
EE
FF
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
Canopy Lock
Ring
x1
Ceiling Canopy
x1
HH
Quick Link
x2
II
GG
Fixture Chain
x1
Figure 1
STEP 1 Install Fixture Loop-
A. Thread the Fixture Loop (A) onto the top
center of the Fixture Body (B). Hand
tighten until snug.
STEP 3 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end of
the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place
another Lock Washer (BB) over the Nipple (DD) and then thread the
Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about
Step B
Step A
CC
BB
EE
II
FF
AA
BB
CC
DD
Figure 3
0.375” above the Crossbar
(AA).
C. Remove the Canopy Lock
Ring (FF) from the Canopy
Chain Loop (EE). Place the
Ceiling Canopy (II) over the
Canopy Chain Loop (EE)
against the ceiling to
determine the correct
position of the Nipple (DD).
Thread the Canopy Lock Ring
onto the Canopy Chain Loop
(EE). Adjust the Nipple (DD)
to allow the Ceiling Canopy
(II) to rest against the ceiling
when held in place by the
Canopy Lock Ring (FF).
D. Remove the Canopy Lock
Ring (FF) and the Ceiling
Canopy (II). Tighten the Hex
Nut (CC) against the
Crossbar (AA) to secure in
place.
STEP 4 - Install Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
links if needed.
E
D
F
C
Steel Collar
x5
Socket Collar
x5
Shade
x5
Socket Collar
Tool x 1
B
Fixture Body
x1
A
Fixture Loop
x1
A
B
Figure 2
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
STEP 2 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
August2015