Installation Sheet

ManualsBrandsQuoizel ManualsPendantsQuoizel Annex Single Light 9" Wide Cage Mini Pendant

1of2

For Style ANX1509AN

Package Contents

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Pleasegoto forproductcleaningtips.Gotothe selection.

(1)A19MediumBaseBulb100WMaximum,MediumBaseVintageBulbisrecommended,bulbnotincluded.

MinimumHangingHeightis13.75”,MaximumHangingHeightis52”.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

www.quoizel.com Care+Maintenance

LightSource:

FixtureHangingHeight:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Installation Guide #IS-ANX1509AN

2018 QuoizelInc.

ReleasedDate:2018-10-08

visit us on-line at www.quoizel.com

Socket Collar

Mesh Shade

Ceiling Canopy

6” Rod

12” Rod

Crossbar

Assembly

Fixture Body

STEP 1 Install Ceiling Canopy and

Rods to Fixture Body

A. By using Allen Wrench (H), double

check set screws on the joint of the

Fixture Body (E) to make sure they

are tighten properly.

B. Tighten the lock screw to secure the

joint of the Fixture Body (E).

C. Determine the Rods (B/C) to be

assembled to the Fixture Body (E)

according to your hanging height.

Figure 1

Supply Wires

and Ground Wire

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

STEP 2 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-

eiling Canopy to the

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

C (D) Crossbar Assembly (A) and secure with

mounting balls. Note: The should be snug

against the and the mounting balls. If

Ceiling Canopy (D)

not, adjust the length of

the nipple on the Crossbar Assembly (A) by unscrewing the

preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

achieved. Once the Ceiling Canopy (D) is secure, remove the

mounting ball and Ceiling Canopy (D).

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Ceiling

Canopy

Figure 2

Figure 3

Allen Wrench

Lock Screw Set Screw

Set Screw

D. Pass the supply wires and

ground wire through the

chosen rods (B/C) and the

Ceiling Canopy (D). Thread

the Fixture Body (E), the

chosen Rods (B/C) and the

Ceiling Canopy (D)

together. Hand tighten until

snug.

Joint

(Step 1 Continued)

Suggested rods for Ceiling height :

8’ ceiling : use (1) 6” rod and (1) 12” rod

9’ ceiling : use (1) 6” rod and (2) 12” rods

10’ ceiling : use (2) 6” rods and (2) 12” rods

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-ANX1509AN For Style ANX1509AN Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (1) A19 Medium Base Bulb 100W Maximum, Medium Base Vintage Bulb is recommended, bulb not included. Fixture Hanging Height: Minimum Hanging Height is 13.75”, Maximum Hanging Height is 52”.
PAGE 2
STEP 4 - Wire Connections STEP 7 - Adjust Mesh Shade Direction A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. A.