Installation Sheet

ManualsBrandsQuoizel ManualsChandeliersQuoizel Anthem 6 Light 24-3/4" Wide Ring Chandelier

1of3

Assembly Instruction Sheet #IS-ATH5006K

For Style ATH5006K

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

2017 QuoizelInc.

ReleasedDate:2017-11-06

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

Pleasegoto forproductcleaningtips.Gotothe selection.

(6)B10CandelabraBaseBulbs60WMaximumor

(6)CandelabraBaseT8Vintage Bulbs are recommended but not supplied.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Fixture Loop

6” Rod

Fixture Body

12” Rod

Allen Screw

Cover

Support Arms

Assembly

STEP 1 Install Cover, Support Arms Assembly and Fixture Body

together

A. Unfold support arms to proper locations (Refer to SUPPORT ARMS

DISTRIBUTION).

B. Carefully pull black and white wires with ground wire out of support

arms. Attach the tabs at the ends of support arms into the ring of the

Fixture Body (G). Align holes on tabs to mounting holes on the ring.

Secure by threading Allen Screws (D) into mounting holes. Hand

tighten until snug with screwdrivers.

C. Tuck all slack wires inside of the fixture canopy on the top of the

Support Arms Assembly (F). Thread the Cover (E) onto the hex

coupling on the top center of the Support Arms Assembly (F). Hand

tighten until snug.

Mounting Hole

Hex Coupling

Tab

SUPPORT ARMS DISTRIBUTION

Support Arm

Figure 1

Hardware Contents

Crossbar

Assembly

Ceiling

Canopy

Quick Link

Summary of content (3 pages)

PAGE 1
Assembly Instruction Sheet #IS-ATH5006K For Style ATH5006K 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (6) B10 Candelabra Base Bulbs 60W Maximum or (6) Candelabra Base T8 Vintage Bulbs are recommended but not supplied.
PAGE 2
STEP 2 - Install Fixture Loop and Rods to Fixture Body STEP 4 - Install the Fixture Body and Ceiling Canopy A A. Determine the Rods (B/C) to be assembled to the coupling on the top center of the fixture according to your hanging height. B. Pass the supply wires and ground wire through the chosen rods (B/C) and the Fixture Loop (A). Thread the fixture, the chosen Rods (B/C) and the Fixture Loop (A) together. Hand tighten until snug. B B C Supply Wires and Ground Wire C Coupling A.
PAGE 3
STEP 6 - Install Bulbs A. Insert bulbs onto sockets and screw snugly into place. T8 Vintage Bulb (recommended but not supplied) Your fixture is now assembled and ready to use. Enjoy! Socket Figure 6 ATH5006K FINISH: MYSTIC BLACK NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" 6” Dia. 65.75” OVERALL HEIGHT INCLUDES SINGLE CHAIN, QUICK LINK, (2) 6” RODS AND (2) 12” RODS 24” 24.75” Dia. NOTE: TWO LIGHTS ARE SHOWN FOR REFERENCE ONLY. 2017 QuoizelInc. Thank you for purchasing a Quoizel product.