Installation Sheet

1of2
For Style AVY1714BN
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(4)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Installation Guide #IS-AVY1714BN
2018 QuoizelInc.
visit us on-line at www.quoizel.com
Package Contents
A
Crossbar Assembly
x1
Fixture Body
x1
B
STEP 1 - Installing the Crossbar
Assembly
A. Pass the supply wires from outlet
box through the Crossbar
Assembly (A). Attach the Crossbar
Assembly (A) to the Outlet Box with
the head of the Green Ground
Screw facing you. Secure the
Crossbar Assembly (A) with Outlet
Box Screws (not included). Tighten
until snug.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 1
STEP 2 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
Canopy to the
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
Crossbar Assembly (A) and secure with
mounting balls. Note: The should be snug against
the and the mounting balls. If
Fixture
Fixture Canopy
not, adjust the length of the
nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Fixture Canopy is secure, remove the mounting
ball and Fixture Canopy and proceed to Step 3.
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
Figure 2
Fixture Canopy
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
Figure 4
Fixture Canopy
STEP 3 - Wire Connections
A.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 4 Install the Fixture-
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy (D) over the outlet box. Align the holes in the ceiling canopy
with the mounting screws, then attach the Ceiling Canopy (D) using
the previously removed mounting balls. Hand tighten until snug.
STEP 5 Install the Bulb-
A. Insert the bulb onto the socket
and screw snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
Figure 5
Bulb (not included)
C
Optional
Candle Cover
x4
ReleasedDate:2019-02-21