Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Awning 3 Light 15" Wide Semi-Flush Ceiling Fixture

Package Contents

Warnings and Cautions

1of2

For Style AW1715MB

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Crossbar

Assembly

Pleasegoto forproductcleaningtips.Gotothe selection.

(3)A19MediumBaseBulbs100WMaximum,MediumBaseVintageBulbsarerecommended,bulbsnotincluded.

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Installation Guide #IS-AW1715MB

2018 QuoizelInc.

ReleasedDate:2018-09-12

visit us on-line at www.quoizel.com

Fixture Body

Finial

Stem with

Hex Nut

Shade

Cap

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

STEP 2 Test Fitting Ceiling Canopy to Crossbar Assembly-

A. Remove mounting balls from the Crossbar Assembly (A). Fit the

ceiling canopy and Fixture Body (B) to the Crossbar Assembly (A)

and secure with mounting balls. Note: The ceiling canopy should be

snug against the ceiling and the mounting balls. If not, adjust the

length of the nipple on the Crossbar Assembly (A) by unscrewing

the preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

Hex Nut

Mounting Screw

Hex Nut and Lock Washer

Mounting Ball

Ceiling Canopy

Figure 2

Figure 1

STEP 1 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

(Step 2 Continued)

achieved. Once the ceiling canopy and Fixture Body (B) is secure,

remove the mounting ball and Fixture Body (B).

Figure 4

STEP 3 - Wire Connections

A. Wrap bare or green ground wire around green ground screw on the

crossbar, no less than 2 inches from the end of the wire. Tighten the

green ground screw.

B. Use standard wire connectors (not included) to make all wire

connections. Twist connectors until wires are tightly joined together.

Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

Green Ground Screw

on the Crossbar

White wire

from outlet box

White wire

from fixture

Black wire from

outlet box (or Red)

Black wire

from fixture

Bare, or Green

Ground wire

from outlet box

Ground wire

from Fixture

Figure 3

STEP 4 - Install Fixture to Ceiling

A. Carefully tuck all wires into the outlet box and position the ceiling

canopy over the outlet box. Align the holes in the ceiling canopy with

the mounting screws, then attach the ceiling canopy using the

previously removed mounting balls. Hand tighten until snug.

Mounting Screw

Mounting Ball

Ceiling Canopy

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-AW1715MB For Style AW1715MB Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) A19 Medium Base Bulbs 100W Maximum, Medium Base Vintage Bulbs are recommended, bulbs not included. Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
STEP 5 - Install Bulbs, Stem with Hex Nut, Shade and Cap B A. Thread beaded end of the Stem with Hex Nut (C) onto the coupling on the bottom center of the Fixture Body (B). Hand tighten until snug. B. Insert bulbs onto sockets and screw snugly into place. C. Place the Shade (D) over the end of the Stem (C) and secure with the Hex Nut (E). Hand tighten until snug. D. Place the Cap (F) over the end of the Stem (C) and secure with the Finial (G). Hand tighten until snug.