Installation Guide

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-AX1716PN_R1
For Style AX1716PN
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Crossbar Assembly
x1
Mounting
Screw
Hex Nut and
Lock Washer
Mounting
Ball
A
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)A19MediumBase100WMaximum.AlternateBulbs(3)23WCFL.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
B
Figure 3
B
Ceiling
Canopy
x1
C
Spacer
Tube
x1
D
Nipple with
Hex Nut
x1
E
Socket Assembly
x1
F
Drop with
Triangle Hook
(1pc Replacement
String Included)
x25
G
Drop with
Fishhook
(1pc Replacement
String Included)
x49
STEP 5 Attach Drops
onto Fixture
Loop
-
A. Attach Drop with Triangle
Hook (F) to holes on first
layer on the Socket
Assembly (E) properly.
B. Attach Drop with
Fishhook (G) to holes on
other Layers on the
Socket Assembly (E)
properly.
Figure 5
Hole on
First Layer
F
G
E
STEP 1 Attach Ceiling,
Tube and
Socket
Assembly
-
A. Threading have hex nut
end of Nipple with Hex
Nut (D) onto Socket
Assembly (E). Hand
tighten until sung.
B. Place Tube (C) over the
Nipple properly then
Threading Ceiling onto
the Nipple. Hand
tighten until sung.
B
C
D
E
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar
Assembly (A). Attach the Crossbar
Assembly (A) to the Outlet Box with the
head of the Green Ground Screw facing
you. Secure it with Outlet Box Screws (not
included). Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 2
STEP 3 Fit Ceiling Canopy to Crossbar Assembly-
A.
eiling Canopy (B) to the
eiling Canopy
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
C Crossbar Assembly (A) and secure with
mounting balls. Note: The C should be snug
against the and the mounting balls. If
(B)
not, adjust the length
A
Figure 2
of the nipple on the
Crossbar Assembly (A)
by unscrewing the
preassembled hex nut
and lock washer and
then screwing the
mounting screws in or
out of the crossbar until
the correct length is
achieved. Once the
Ceiling Canopy (B) is
secure, remove the
mounting ball and
ceiling canopy and
proceed to Step 5.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
2016 QuoizelInc.
RevisedDate:2016-07-07
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com