Installation Guide

Package Contents
Warnings and Cautions
1of2
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
D
Socket
Assembly
x1
C
Backplate
with Arm
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
Integrated14WLED.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Contactyouroriginalplaceofpurchase.
STEP 1 Attach Socket
Assembly to Arm
-
A. Pull supply wires from the
backplate. Thread Socket
Assembly (D) onto the arm. As
you assemble the parts together
to remove the excess cord
between parts.
Supply wires
Backplate
C
D
Figure 1
A
Crossbar Assembly
x1
B
Alternate
Mounting
screw
x2
STEP 2 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Figure 2
STEP 3 Test Fit the Backplate to the Crossbar Assembly-
A. Remove the mounting balls from the Crossbar Assembly (A).
Place the backplate onto the Crossbar Assembly (A) and secure
with mounting balls. Note: The backplate should be snug against
the wall and held tight with the mounting balls. If it is not, adjust
the length of the mounting screw or alternate short mounting
screw on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws or alternate short mounting screws in or out of
the crossbar until the correct length is achieved. Once the
backplate is secure, remove the mounting ball and backplate and
proceed to Step 4.
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 3
Mounting Screw
or Alternate Short
Mounting Screw
Mounting Screw
or Alternate Short
Mounting Screw
A
Outlet
Box
STEP 4 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 4
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
120v/50-60Hz
MAX90
120v/50-60Hz
MAX90
Supply wires
For Style BCE8414GV
Installation Guide #IS-BCE8414GV
2019 QuoizelInc.
ReleasedDate:2019-01-04
visit us on-line at www.quoizel.com