Installation Guide

ManualsBrandsQuoizel ManualsChandeliersBCN2820WT

Pleasegoto forproductcleaningtips.Gotothe selection.

(4)A19MediumBase100WMaximum.AlternateBulbs(4)23WCFL.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

1of2

Assembly Instruction Sheet #IS-BCN2820WT

For Style BCN2820WT

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2015 QuoizelInc.

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Package Contents

Hardware Contents

Canopy

Chain Loop

Canopy Lock

Ring

Ceiling

Canopy

Quick Link

August2015

Fixture Chain

Side Arm

Socket

Assembly

Cage

Shade

Fixture Loop

Assembly

Center Stem

Crossbar

Lock Washer

Hex Nut

Nipple

28mm 12Ga28mm 12Ga

QUOIZEL

GND

STEP 1 Assemble Fixture Loop Assembly,

Center Stem and Socket Assembly together

A. Thread the Fixture Loop Assembly (A), the

Center Stem (C) and the Socket Assembly (B)

together as shown. Hand tighten until snug.

Figure 1

Figure 2

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

STEP 2 Install Crossbar-

(Step 2 Continued)

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included) Tighten until snug..

STEP 3 Install Canopy Chain Loop and Nipple-

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end of

the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the

Nipple (DD). By using pliers, thread the Hex Nut (CC) against the

Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place

another Lock Washer (BB) over the Nipple (DD) and then thread the

Step

Figure 3

Nipple (DD) into the Crossbar (AA)

until the Nipple (DD) is about

0.375” above the Crossbar (AA).

C. Remove the Canopy Lock Ring

(FF) from the Canopy Chain Loop

(EE). Place the Ceiling Canopy (II)

over the Canopy Chain Loop (EE)

against the ceiling to determine the

correct position of the Nipple (DD).

Thread the Canopy Lock Ring onto

the Canopy Chain Loop (EE).

Adjust the Nipple (DD) to allow the

Ceiling Canopy (II) to rest against

the ceiling when held in place by

the Canopy Lock Ring (FF).

D. Remove the Canopy Lock Ring

(FF) and the Ceiling Canopy (II).

Tighten the Hex Nut (CC) against

the Crossbar (AA) to secure in

place.

STEP 4 - Install Fixture Chain and Ceiling Canopy

A. Adjust the Fixture Chain (GG) to your desired length by removing

links if needed.

Pliers is required for this step.

B. With the Fixture Chain (GG) not attached to the Fixture Loop and the

Canopy Chain Loop (EE), pull the supply wires through the Fixture

Chain (GG) alternating links. After the wires are through the Fixture

Chain (GG), pull the Supply Wires and the Ground Wire through the

Canopy Lock Ring (FF) and the Ceiling Canopy (II) in order.

C. Attach one end of the Fixture Chain (GG) to the Fixture Loop with

one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up and

attach the other end of the Fixture Chain (GG) onto the Canopy

Chain Loop (EE) with another Quick Link (HH). The fixture will now

hang safely. Close the chain loop at the Ceiling Canopy Loop (EE).

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-BCN2820WT For Style BCN2820WT 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (4) A19 Medium Base 100W Maximum. Alternate Bulbs (4) 23W CFL.
PAGE 2
(Step 4 Continued) STEP 7 - Install Bulb D. Feed the Supply Wires and Ground Wire through the Canopy Chain Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving Approximately 8” of wire extending Supply from the Outlet Box. Wires and E. Refer to Step 5 for wire Ground Wire connections. F. Raise the Ceiling Canopy (II) and Canopy Lock Ring (FF) up the GG Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until tight. A.