Installation Sheet

1of2
Assembly Instruction Sheet #IS-BEC8409SBK_R1
For Styles BEC8409SBK
2017 QuoizelInc.
RevisedDate:2017-05-05
Package Contents
B
Lock Screw
x4
Inner Backplate
x1
A
C
Fixture Body
x1
Front/Back
Glass Panel
x2
Side Glass
Panel
x2
D
E
STEP 1 Install Glass-
A. Unlock the Mounting Ball,
remove the Cage from the
Fixture Body (C).
B. Insert Glass Panels (D/E) into
slots in the bottom edge of the
Cage. Fold Tabs on the top
edge of the Cage to secure
Glass Panels.
C. Attach the Cage with Glass
Panels back onto fixture hood
and secure by threading the
Mounting Ball onto the Bolts.
Hand tighten until snug.
C
D
Cage
Mounting Ball
Figure 1
E
Tab
Slot
Bolt
B
STEP 2 Install Inner Backplate
and Fixture Body
-
A. Pass the supply wires with
Ground Wire through Inner
Backplate (A). Attach Inner
Backplate (A) to Outlet Box with
the head of Green Ground
Figure 2
A
Outlet Box
Outlet Box Screw
(not supplied)
Supply Wires
with Ground Wire
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Pleasegoto forproductcleaningtips.Gotothe selection.www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Integrated14WLED
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
EstimatedAssemblyTime:
Preparation:
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Screw facing you.
Secure it with Outlet
Box Screws (Not
included). Tighten
until snug with
screwdrivers
B.RefertoStep3for
wiring connections.
.
C
(Step 2 Continued)
C. Attach the Fixture Body (C) over the Inner Backplate (A) and secure
with Lock Screws (B). Tighten until snug with screwdrivers.
Backplate
Exterior
Grade Caulk
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Bare, or Green
Ground wire
from outlet box
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar
Figure 4
STEP 4 - Apply Silicone Sealer
A. Make sure exterior wall surface and fixture backplate are free of dirt
before applying caulk. Using exterior grade caulk, caulk over top of
backplate and down other side. Do not caulk bottom of fixture
backplate to ensure proper moisture drainage.
Your fixture is now assembled
and ready to use. Enjoy!