Installation Guide

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-BFD8410
For Styles BFD8410PN and BFD8410K
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Crossbar Assembly
x1
Pleasegoto forproduct cleaningtips. Goto the selection.
(1)A21MediumBase bulb150W Maximum,Alternatebulb(1) 42WCFL.
20-30minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
www.quoizel.com Care+ Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecan onlybe mountedin thedirection indicatedon page2.
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver, pliers,wire cutters,wire strippers,electrical tape,safety glasses.
B
Fixture Body
x1
April2015
STEP 1 Remove Styrene
Foam
-
A LockScrewon
the Fixture Body
Fixture Hood
B.Discard Styrene Foam
from Shade
C.Reverse above steps to
reinstall the Fixture Hood
onto fixture.
.Unscrew
and
remove .
.
Figure 1
Fixture
Hood
Lock
Screw
Styrene
Foam
Shade
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 2
A
STEP 3 Fit Backplate to Crossbar Assembly-
A.
on Fixture Body (B) to the
Remove mounting balls from the Crossbar Assembly (A). Fit the
backplate Crossbar Assembly (A) and
secure with mounting balls. Note: The backplate
should be snug against the wall and the mounting balls. If
on Fixture Body (B)
not,
adjust the length of the nipple on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws in or out of the crossbar until the
Correct length is achieved.
Once the backplate on
Fixture Body (B) is secure,
remove the mounting ball
and Fixture Body (B) and
proceed to Step 4.
Figure 3
Mounting
Screw
B
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
Mounting Screw
B
Mounting
Ball
A
Backplate
Figure 5
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the
outlet box and position the
backplate of fixture body (B)
over the outlet box. Align the
holes in the backplate with the
mounting screws. Place caulk
(not supplied) into the
previously removed mounting
balls and then attach fixture
body (B) using the mounting
balls. Hand tighten until snug.