Installation Guide

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-BGD1716WT
For Style BGD1716WT
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Crossbar
Assembly
x1
D
Edison
Bulb
x3
C
Shade
x1
B
Socket
Assembly
x1
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
January2016
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the
Crossbar Assembly (A). Attach the
Crossbar Assembly (A) to the Outlet
Box with the head of the Green
Ground Screw facing you. Secure it
with Outlet Box Screws (not included).
Tighten until snug.
Supply
Wires with
Ground Wire
Outlet
Box Screws
(not included)
Outlet
Box
Figure 1
STEP 3 Fit Ceiling Canopy to Crossbar Assembly-
A.
eiling canopy of the Socket Assembly (B) to the
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
c Crossbar
Assembly (A) and secure with mounting balls. Note: The
should be snug against the
and the mounting balls. If not, adjust the length of the nipple
ceiling
canopy of the Socket Assembly (B)
Mounting
Screw
Hex Nut and
Lock Washer
B
Mounting Ball
Figure 3
A
(Step 3 Continued)
on the Crossbar Assembly (A) by unscrewing the preassembled hex
nut and lock washer and then screwing the mounting screws in or
out of the crossbar until the correct length is achieved. Once the
is secure, remove the
mounting ball and ceiling canopy and proceed to Step 4.
ceiling canopy of the Socket Assembly (B)
A
Pleasegoto forproduct cleaningtips. Goto the selection.
(3)Medium BaseDecorative Filament60W bulb(provided), Maximum100W,Alternate bulb(3) 23WCFLMaximum.
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
www.quoizel.com Care+ Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver, pliers,wire cutters,wire strippers,electrical tape,safety glasses.
GND
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
STEP 2 Attach Shade to Socket
Assembly
-
A. Attach Loops on the top edge of
the Shade (C) to Hooks on ends
of Side Rods on the Socket
Assembly (B). Carefully release
your hands before the Shade (C)
is hung properly.
Figure 2
B
C
Side
Rod
Loop
Hook
STEP 5 - Install Fixture to Ceiling
A. Carefully tuck all wires into the outlet
box and position the ceiling canopy of
the Socket Assembly (B) over the
outlet box. Align the holes in the
ceiling canopy with the mounting
screws. Secure the ceiling canopy
with Mounting Balls. Hand tighten
until snug.
Mounting
Screw
B
Mounting Ball
A
Figure 5