Installation Guide

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-BGS1715RK
For Style BGS1715RK
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Crossbar Assembly
x1
B
Shade
x1
C
Ceiling Canopy
Assembly
x1
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
July2015
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar
Assembly (A). Attach the Crossbar
Assembly (A) to the Outlet Box with the
head of the Green Ground Screw facing
you. Secure it with Outlet Box Screws (not
included). Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 2
STEP 3 Fit Ceiling Canopy to Crossbar Assembly-
A.
eiling Canopy (C) to the
eiling Canopy
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
C Crossbar Assembly (A) and secure with
mounting balls. Note: The C should be snug
against the and the mounting balls. If
(C)
not, adjust the length of
the nipple on the Crossbar Assembly (A) by unscrewing the
Mounting
Screw
Hex Nut and
Lock Washer
Mounting
Ball
A
(Step 3 Continued)
preassembled hex nut and
lock washer and then
screwing the mounting
screws in or out of the
crossbar until the correct
length is achieved. Once
the Ceiling Canopy (C) is
secure, remove the
mounting ball and ceiling
canopy and proceed to
Step 4.
A
Pleasegoto forproduct cleaningtips. Goto the selection.
(3)B10 CandelabraBase 60WMaximum.
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
www.quoizel.com Care+ Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver, pliers,wire cutters,wire strippers,electrical tape,safety glasses.
D
Tube
x1
E
Socket Assembly
x1
F
Ring
x1
STEP 1 Install Ceiling Canopy
Assembly, Tube and Socket Assembly
-
A. Pass supply wires through the Tube (D)
and the Ceiling Canopy Assembly (C).
B. Thread the Tube (D) onto the Socket
Assembly (E) and hand tighten until snug
C. Thread the Ceiling Canopy Assembly (C)
onto the top end of the Tube (D) and hand
tighten until snug.
.
C
D
E
Figure 1
C
Figure 5
STEP 5 Install Fixture to Ceiling-
A. Carefully tuck all wires into the
outlet box and position the Ceiling
Canopy (C) over the outlet box.
Align the holes in the Ceiling
Canopy (C) with the mounting
screws. Secure the
with Mounting Balls.
Hand tighten until snug.
Ceiling
Canopy (C)
Mounting
Screw
Mounting
Ball
A
C
Figure 3

Summary of content (2 pages)