Installation Guide

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-BKH1714WT
For Style BKH1714WT
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Crossbar
Assembly
x1
E
Shade
x1
C
Side
Chain
x4
D
Socket
Assembly
x1
B
Canopy
x1
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
July2014
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar
Assembly (A). Attach the Crossbar Assembly
(A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it
with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 2
STEP 3 Fit Ceiling Canopy to
Crossbar Assembly
-
A.
(B) to the
ceiling
Remove mounting balls from the
Crossbar Assembly (A). Fit the
Canopy Crossbar
Assembly (A) and secure with
mounting balls. Note: The
Canopy should be snug
against the and the
mounting balls. If
(B)
not, adjust the
Mounting Screw
Hex Nut and
Lock Washer
B
Mounting
Ball
Figure 3
A
length of the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Canopy (B) is secure, remove the mounting ball
and ceiling canopy and proceed to Step 4.
A
Pleasegoto forproduct cleaningtips. Goto the selection.
(3)A19MediumBase bulb100W Maximum,Alternatebulb(3) 23WCFL.
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
www.quoizel.com Care+ Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver, pliers,wire cutters,wire strippers,electrical tape,safety glasses.
STEP 1 Attach Canopy and
Socket Assembly
together
-
A. Threading Canopy (A) onto the
nipple on the top of Socket
Assembly (A). Tighten until snug.
Figure 1
A
D
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the
outlet box and position the
Ceiling Canopy over the outlet
box. Align the holes in the
Ceiling Canopy with the
mounting screws, then attach
the Ceiling Canopy using the
previously removed mounting
balls. Hand tighten until snug.
Figure 5
Mounting
Screw
A
Mounting
Ball
Ceiling
Canopy
STEP 6 - Install Shade, Fixture
Body and Side Arm
together
A. Place one end of Side Chain
(C) onto the hook on the side
of Canopy (B), the other end
of Side Chain (C) on to the
hook in the Shade (E)
properly.
B.
100
This fixture uses standard
bulb with a medium screw
base. Maximum watts.
Insert bulb and screw snugly
into place.
Your fixture is now assembled
and ready to use. Enjoy!
Figure 6
B
C
E
Hook
Hook