Installation Guide

1of2
Assembly Instruction Sheet #IS-BKR8408K
For Style BKR8408K
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Pleasegoto forproduct cleaningtips. Goto the selection.
(1)Medium BaseDecorative Filament60W bulb(provided), Maximum100W,Alternate bulb(1) 23WCFLMaximum.
20-30minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
www.quoizel.com Care+ Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecan onlybe mountedin thedirection indicatedon page2.
ToolsRequired: Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters,wire strippers,electrical tape,safety glasses.
Package Contents
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Crossbar
Assembly
x1
Fixture
Body
x1
September2015
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 1
A
Shade
x1
E
Socket Collar
x1
G
Edison
Bulb
x1
D
Wahser
x1
B
Alternate
Mounting
screw
x2
C
F
Mounting Screw
or Alternate Short
Mounting Screw
STEP 2 Fit Backplate to
Crossbar Assembly
-
A.
on Fixture
Body (C) to the
Remove mounting balls from
the Crossbar Assembly (A).
Fit the backplate
Crossbar
Assembly (A) and secure with
Figure 2
Mounting Screw
or Alternate Short
Mounting Screw
C
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
mounting balls. Note: The
backplate
should be snug against the wall
and the mounting balls. If
on Fixture Body (C)
not,
adjust the length of the mounting
screw or alternate short mounting
screw on the Crossbar Assembly
(A) by unscrewing the
preassembled hex nut and lock
(Step 2 Continued)
washer and then screwing the mounting screws or alternate short
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate on Fixture Body (C) is secure, remove
the mounting ball and Fixture Body (C) and proceed to Step 3.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
Figure 4
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into the outlet box and position the backplate
of fixture body (D) over the outlet box. Align the holes in the
B
Mounting Ball
A
Mounting Screw
or Alternate Short
Mounting Screw
Backplate
STEP 5 Install Shade to Fixture Body-
A. Place Shade (D) and the Washer (E) over the Socket as shown.
Secure by threading the Socket Collar (F) onto the Socket. Hand
tighten until sung.
B. This fixture uses Medium Base Decorative Filament 60W bulb (G),
backplate with the mounting
screws or alternate short
mounting screws. Secure
with the previously
removed mounting balls
and hand tighten until
snug.