Installation Guide

Nipple
B
D
E
1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Package Contents
Pleasegoto forproduct cleaningtips. Goto the selection.
(1)Medium BaseDecorative Filament60W bulb(provided), Maximum150W,Alternate bulb(1) CFLMaximum.
www.quoizel.com Care+ Maintenance
LightSource:
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape, safetyglasses.
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 Attach Fixture Body to
Post
-
A. Coat the top 1” of the Post with
Clear Silicone Caulk (not supplied)
and position the Post Fitter onto
the Post. Be sure to seat it
completely, aligning the holes in
the Fitter with the 1/16” Pilot Holes
drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws (A).
Your fixture is now assembled and
ready to use. Enjoy!
A
Mounting Screw
x3
Assembly Instruction Sheet #IS-BKR9010K
For Style BKR9010K
Post
Post Fitter
Figure 5
Mounting Hole
A
November2015
STEP 3 Drill Pilot Holes on Post-
A. Carefully fit the Post Fitter over the
end of the Post (not supplied),
making sure the Post Fitter is fully
seated.
B. Mark the drill point for the (3)
Mounting Screws, using (3)
Mounting Holes as reference. After
marking hole locations, remove
fixture from post and drill 1/16” pilot
holes for screws.
Figure 3
Post
Post Fitter
Mounting Hole
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
B
Finial
x1
STEP 1 remove the
Ring from
Fixture Body
-
A. Unscrew Lock Ball
and Lock Screw from
Fixture Body to
remove the Ring.
Figure 1
C
Waterproof
Washer
x1
D
Top
Cap
x1
E
Outer
Cap
x1
F
Bracket
x1
G
Fixture
Body
x1
H
Shade
x1
I
Edison
Bulb
x1
Fixture
Body
Ring
Lock Ball
Lock
Screw
STEP 2 Assembly Shade to
Fixture Body
-
A. This fixture uses Medium Base
Decorative Filament 60W bulb (I),
Maximum 150W. Insert bulb and
screw snugly into place.
B. Place the Shade (H) in to the
Fixture Body (G).
Bracket F
C. Reinstall Lock Screw onto the
Fixture Body (G).
D. E
and Waterproof Washer (C)
Bracket
Place the Ring,
the ( ) over the Bolt on the
Fixture Body (G) properly, secure
by threading Lock Ball onto the
Bolt, hand tighten until sung.
Place Outer Cap ( ), Top Cap (C)
onto
the Nipple on the top of (E),
secure by threading Finial (B) onto
the Nipple. hand tighten until sung.
Figure 2
F
H
G
Ring
Lock
Ball
Lock
Screw
C