Installation Sheet

ManualsBrandsQuoizel Manualspost lightsBKR9010K

Package Contents

Warnings and Cautions

1of3

For Style BKR9010IA

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Pleasegoto forproductcleaningtips.Gotothe selection.

markingpen,1/16”

drillbit,centerpunch,hammer,drillandwrench.

(1)A21MediumBaseVintageBulb150WMaximum,bulbincluded.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses,

Fixture

Body

Installation Guide #IS-BKR9010IA

2019 QuoizelInc.

ReleasedDate:2019-01-30

visit us on-line at www.quoizel.com

Mounting Screw

Glass

Shade

Finial

Waterproof

Washer

Top Cap

Fixture Hood

Bracket

Edison Bulb

STEP 1 remove the Ring from Fixture Body-

A. Unscrew lock balls and lock screws from fixture body to remove the

ring.

Figure 1

Fixture Body

Ring

Lock Ball

Lock Screw

Nipple

STEP 2 Install- Glass Shade and Fixture Hood

A. Insert the bulb onto the socket and screw snugly into place.

B. Place the Glass Shade (H) into the Fixture Body (I). Place the ring

and the Bracket (F) over the bolt on the Fixture Body (I) properly.

Secure by threading previously removed lock balls onto the bolts.

Hand tighten until sung.

C. Reinstall previously removed lock screws onto the Fixture Body (I).

D. Place the Fixture Hood (E), the Top Cap (D) and the Waterproof

Washer (C) onto the nipple on the top of Bracket (F). Secure by

threading the Finial (B) onto the nipple. Hand tighten until sung.

Figure 2

Lock Ball

Lock Screw

Ring

Summary of content (3 pages)

PAGE 1
Installation Guide #IS-BKR9010IA For Style BKR9010IA Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses, marking pen, 1/16” drill bit, center punch, hammer, drill and wrench. Light Source: (1) A21 Medium Base Vintage Bulb 150W Maximum, bulb included.
PAGE 2
STEP 3 - Install Fixture Hood and Top Cap STEP 6 - Drill Holes B C D A. Place the Fixture Hood (E), the Top Cap (D) and the Waterproof Washer (C) over the nipple on the Bracket (H) in turn. Secure by threading the Finial (B) onto the nipple. Hand tighten until snug. A. Using the 1/16” bit and drill, drill a pilot hole completely through the post at each (3) locations marked in step 5 above. E 1/16” bit and drill H Post Figure 6 STEP 7 - Wire Connections A.
PAGE 3
BKR9010IA NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" FINISH: INDUSTRIAL ALUMINUM 10.5” 9”Dia. 6.5”Dia. 10.25” 19.25” 2019 QuoizelInc. visit us on-line at www.quoizel.