Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.
(1)MediumBaseDecorativeFilament60Wbulbs(provided),Maximum100W,Alternatebulb(1)23WCFLMaximum.
www.quoizel.com Care+Maintenance
LightSource:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
EstimatedAssembly Time:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-BNS1505WT
For Style BNS1505WT
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
August2015
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Bulb
x1
Socket
Assembly
x1
D
Package Contents
12” Rod
x2
Hardware Contents
Figure 1
Supply Wires
and Ground Wire
A
D
C
AA
BB
CC
DD
EE
FF
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
Canopy Lock Ring
x1
Ceiling Canopy
x1
GG
Quick Link
x1
STEP 1 Assemble Rods and the
Fixture Loop
-
A. Determine the Rods (B/C) to be
assembled to the Socket Assembly
(D) according to your hanging height.
B. Pass the supply wires and ground
wire through the chosen rods (B/C)
and the Fixture Loop (A). Thread the
Socket Assembly (D), the chosen
Rods (B/C) and the Fixture Loop (A)
together. Hand tighten until snug.
Suggested rods for Ceiling height :
8’ ceiling : use (2) 12” rods
9’ ceiling : use (2) 6” rods and (2) 12”
rods
A
Fixture
Loop
x1
B
B
HH
28mm 12Ga28mm 12Ga
QUOIZEL
R
GND
F
Socket Collar
x1
E
Shade
x1
B
6” Rod
x2
C
G
STEP 4 - Install Fixture Chain and Ceiling Canopy
A. With the Quick Link (GG) not attached to the Fixture Loop (A) and
the Canopy Chain Loop (EE), pull the supply wires through the
Canopy Lock Ring (FF), the Ceiling Canopy (HH) and the Quick Link
(GG) in order.
C
Figure 2
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
STEP 2 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
STEP 3 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end of
the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place
another Lock Washer (BB) over the Nipple (DD) and then thread the
Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about
Step B
Step A
CC
BB
EE
FF
AA
BB
CC
DD
Figure 3
HH
0.375” above the Crossbar
(AA).
C. Remove the Canopy Lock
Ring (FF) from the Canopy
Chain Loop (EE). Place the
Ceiling Canopy (HH) over the
Canopy Chain Loop (EE)
against the ceiling to
determine the correct position
of the Nipple (DD). Thread the
Canopy Lock Ring (FF) onto
the Canopy Chain Loop (EE).
Adjust the Nipple (DD) to allow
the Ceiling Canopy (HH) to
rest against the ceiling when
held in place by the Canopy
Lock Ring (FF).
D. Remove the Canopy Lock
Ring (FF) and the Ceiling
Canopy (HH). Tighten the Hex
Nut (CC) against the Crossbar
(AA) to secure in place.