Installation Guide

ManualsBrandsQuoizel ManualsSemi-Flush Mount LightsBNS1715WT

Package Contents

Warnings and Cautions

1of2

Assembly Instruction Sheet #IS-BNS1715WT

For Style BNS1715WT

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2015 QuoizelInc.

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Crossbar

Assembly

Pleasegoto forproduct cleaningtips. Goto the selection.

(3)Medium BaseDecorative Filament60W bulbs(provided), Maximum100W,Alternate bulb(3) 23WCFLMaximum.

20-30minutes

Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are

present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement

parts.

www.quoizel.com Care+ Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver, pliers,wire cutters,wire strippers,electrical tape,safety glasses.

Ceiling Canopy

Assembly

August2015

STEP 1 Install Crossbar Assembly-

A. Pass the supply wires through the

Crossbar Assembly (A). Attach the

Crossbar Assembly (A) to the Outlet

Box with the head of the Green

Ground Screw facing you. Secure it

with Outlet Box Screws (not

included). Tighten until snug.

Supply Wires

with Ground Wire

Outlet Box

Screws (not

included)

Outlet Box

Figure 1

STEP 2 Assemble Socket Assembly,

Center Stem and Ceiling Canopy

Assembly

A. Thread one end of the Center Stem (C) into

the coupling on the top center of the

Socket Assembly (D). Hand tighten until

snug.

B. Thread the Ceiling Canopy Assembly (B)

onto the top end of the Center Stem (C)

and hand tighten until snug.

Figure 2

Cage

Socket

Assembly

Center Stem

Bulb

Lock Ball

Nipple

Cap

Finial

STEP 3 Fit Ceiling Canopy to Crossbar Assembly-

to the

Remove mounting balls from the Crossbar Assembly (A). Fit the

ceiling canopy Crossbar Assembly (A) and secure with

mounting balls. Note: The ceiling canopy should be snug against

the ceiling and the mounting balls. If not, adjust the length of the

(Step 3 Continued)

mounting screw on the

Crossbar Assembly (A) by

unscrewing the preassembled

hex nut and lock washer and

then screwing the mounting

screws in or out of the

crossbar until the correct

length is achieved. Once the

ceiling canopy is secure,

remove the mounting ball and

ceiling canopy and proceed to

Step 4.

Mounting

Screw

Ceiling

Canopy

Hex Nut and

Lock Washer

Mounting Ball

Figure 3

White wire

from supply

White wire

from fixture

Black wire from

supply (or Red)

Black wire

from fixture

Ground wire

from supply

Ground wire

from fixture

Figure 4

STEP 4 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Twist

connectors until wires are tightly joined together. Wrap each

connection with approved electrical tape and carefully stuff all the

connected wires into the Outlet Box.

STEP 5 Install Fixture-

A. Carefully tuck all wires into

the outlet box and position

the ceiling canopy over the

outlet box. Align the holes in

the ceiling canopy with the

mounting screws. Secure the

ceiling canopy with Mounting

Balls. Hand tighten until

snug.

Mounting

Screw

Ceiling

Canopy

Mounting Ball

Figure 5

STEP 6 - Attach Cap to Cage

A. Place the Lock Ball (G) inside of the Cage (F). Pass one end of the

Nipple (H) through the hole on the bottom center of the Cage (F)

and thread the Lock Ball (G) onto the Nipple (H). Tighten until

snug.

B. Place the Cap (I) over the end of the Nipple (H) and secure with the

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-BNS1715WT For Style BNS1715WT Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) Medium Base Decorative Filament 60W bulbs (provided), Maximum 100W, Alternate bulb (3) 23W CFL Maximum.
PAGE 2
(Step 6 Continued) BNS1715WT F Finial (J). Hand tighten until snug. H 6” Dia. FINISH: WESTERN BRONZE G I Figure 6 J 15.25” STEP 7 - Install Cage and Bulb A. Place the Cage (F) over the Socket Assembly. Attach ends of Side Arms to the hooks on the top edge of the Cage (F). B. This fixture uses Medium Base Decorative Filament Bulb 60W (E), Maximum 100W. Insert bulb and screw snugly into place. Your fixture is now assembled and ready to use. Enjoy! 2015 QuoizelInc. Side Arm Socket E 15.25” Dia.