Installation Sheet

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Assembly Instruction Sheet #IS-BNT1504WT
For Style BNT1504WT
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBaseBulb75WMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
A
Crossbar Assembly
x1
C
Thank you forpurchasing a Quoizelproduct.
Need assistance withparts or assembly?Call Quoizel customerservice at 1-800-645-3184
or visit us on-line at www.quoizel.com
Fixture Body
x1
2017 QuoizelInc.
ReleasedDate:2017-03-28
STEP 1 - Adjust Fixture Height
A. Unscrew the set screw on the
coupling underside of the ceiling
canopy, move the cord in or out
of the ceiling canopy according
to your desired fixture hanging
height. Once your desired
hanging height is achieved,
tighten the set screw on the
coupling until snug to engage the
cord.
B. Move the wire clasp to the hex
nut in the center of the ceiling
canopy.
C
STEP 2 - Installing the Crossbar
Assembly
A. Pass the supply wires through the
Crossbar Assembly (A). Attach the
Crossbar Assembly (A) to the
Outlet Box with the head of the
Green Ground Screw facing you.
Secure the Crossbar Assembly (A)
with Outlet Box Screws (not
included). Tighten until snug.
Supply
Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
A
Figure 2
Wire Clasp
Ceiling Canopy
Cord
Set Screw
Coupling
Figure 1
STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
eiling canopy to the
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
c and Fixture Body (C) Crossbar Assembly (A)
and secure with mounting balls. Note: The should be
snug against the and the mounting balls. If
ceiling canopy
not, adjust the
length of the nipple on the Crossbar Assembly (A) by unscrewing
the preassembled hex nut and lock washer and then screwing the
Mounting
Screw
Hex Nut and
Lock Washer
Mounting Ball
A
Ceiling
Canopy
mounting screws in or out of
the crossbar until the
correct length is achieved.
Once the ceiling canopy and
Fixture Body (C) is secure,
remove the mounting ball
and ceiling canopy and
Fixture Body (C) and
proceed to Step 4.
Figure 3
B
Lock Screw
x3
D
Shade
x1
STEP 4 Make Wire Connections-
Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
B. If the electrical wire is going to be cut shorter than provided, strip
back the clear wire covering the 3 fixture wires as far as you need to.
This will expose each fixture wire individually. Strip each end of 3
fixture wires.
A.
Figure 4
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Bare, or Green
Ground wire
from outlet box
OR
Ground wire
from Ceiling Canopy
Ground wire
from Ceiling Canopy
Ground wire
from Fixture
Green Ground Screw
on the Crossbar