Installation Guide

ManualsBrandsQuoizel ManualsPendant LightingBNY2816C

Pleasegoto forproductcleaningtips.Gotothe selection.

(3)A19MediumBase100WMaximum,Alternatebulb(3)23WCFL

www.quoizel.com Care+Maintenance

LightSource:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

EstimatedAssembly Time:30-45minutes

1of2

Assembly Instruction Sheet #IS-BNY2816C_R1

For Style BNY2816C

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

2016 QuoizelInc.

RevisedDate:2016-05-06

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering June result.

Shade Assembly

Package Contents

Crossbar

Assembly

6” Rod

12” Rod

Ceiling

Canopy

Center Stem

Rubber

Washer

Flat

Washer

Bottom

Diffuser

Preparation:Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

Top Diffuser

STEP 1 - Attach Top Diffuser to Socket Assembly

Quoizel recommends (2) people for this step.

A. With one person hold Socket Assembly, another person remove Lock

Balls and Washers from Shade Assembly (E). Attach Top Diffuser (J)

Bolt

Socket Assembly

Lock Ball

Washer

onto top of Shade

Assembly (E) and pass

holes over bolts. Secure by

threading Washers and

Lock Balls onto Bolts and

hand tighten until snug.

Figure 1

STEP 2 - Install Ceiling Canopy, Rods and Shade Assembly

together

A. Determine Rods (B/C) to be assembled to the Shade Assembly (E)

according to your hanging height.

B. Pass the supply wires and ground wire

through the chosen rods (B/C) and the

Ceiling Canopy (D). Thread the Shade

Assembly (F), the chosen Rods (B/C) and

the Ceiling Canopy (D) together. Hand

tighten until snug.

Suggested rods for Ceiling height :

8’ ceiling : use (2) 12” rods

9’ ceiling : use (2) 6” rods and (2) 12” rods

Supply Wires

and Ground Wire

Figure 2

STEP 3 Install Crossbar Assembly-

A. Pass the supply wires through the Crossbar Assembly (A). Attach

the Crossbar Assembly (A) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included). Tighten until snug.

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 3

STEP 4 Fit Ceiling Canopy to Crossbar Assembly-

Ceiling Canopy to the

Ceiling Canopy

Remove mounting balls from the Crossbar Assembly (A). Fit the

(D) Crossbar Assembly (A) and secure with

mounting balls. Note: The (D) should be snug

Finial

Hex Nut

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-BNY2816C_R1 For Style BNY2816C Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) A19 Medium Base 100W Maximum, Alternate bulb (3) 23W CFL Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
length of the nipple on the Crossbar Assembly (A) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the Ceiling Canopy (D) is secure, remove the mounting ball and Ceiling Canopy (D) and proceed to Step 5. REPLACE INNER SHADE A Hex Nut and A. Unlock Finial and remove it from fixture. Lock Washer B . Unscrew Hex Nut and remove Flat Washer, Rubber Washer and D Diffuser. Lock C.