Installation Guide

ManualsBrandsQuoizel ManualsPendant LightingBNY2822C

Pleasegoto forproductcleaningtips.Gotothe selection.

(5)A19MediumBase100WMaximum,Alternatebulb(5)23WCFL

www.quoizel.com Care+Maintenance

LightSource:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

EstimatedAssembly Time:30-45minutes

1of3

Assembly Instruction Sheet #IS-BNY2822C_R1

For Style BNY2822C

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

2016 QuoizelInc.

Revised2016-05-06

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering June result.

Shade

Assembly

Package Contents

Crossbar Assembly

6” Rod

12” Rod

Hex Nut

Washer

Ceiling

Canopy

Swivel

Nipple

Stem

Flat

Washer

Finial

Bottom

Diffuser

Assembly Instructions for Pendant Light

(Step 1A - Step 7A)

Figure 1A

Preparation:Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

Note:This CONVERTIBLEfixturecanbemountedaspendantlightorsemi-flushlight.Refertorespective

installationsteps forinstallations.

Top

Diffuser

Rubber

Washer

Bolt

Lock Ball

Washer

STEP 1A - Attach Top Diffuser

to Socket Assembly

Quoizel recommends (2)

people for this step.

Socket Assembly

(Step 1A Continued)

A. With one person hold Socket Assembly, another person remove Lock

Balls and Washers from Shade Assembly (I). Attach Top Diffuser (O)

onto top of Shade Assembly (I) and pass holes over bolts. Secure by

threading Washers and Lock Balls onto Bolts and hand tighten until

snug.

STEP 2A - Install Ceiling Canopy, Rods and Socket Assembly

together

A. Thread Nipple (G) onto Swivel (H). Place Ceiling Canopy (F) and

Washer (E) over Nipple (G), secure by threading Hex Nut (D) onto

Nipple (G), tighten until sung.

B. Determine Rods (B/C) to be assembled to Shade Assembly (I)

according to your hanging height.

Supply Wires and

Ground Wire

STEP 3A Install Crossbar Assembly-

A. Pass the supply wires through the Crossbar Assembly (A). Attach

the Crossbar Assembly (A) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included). Tighten until snug.

Figure 3A

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

C. Pass the supply wires and ground wire

through chosen rods (B/C) and Ceiling

Canopy with Swivel. Thread Shade

Assembly (I), chosen Rods (B/C) and

Ceiling Canopy with Swivel together.

Hand tighten until snug.

Suggested rods for Ceiling height :

8’ ceiling : use (2) 12” rods

9’ ceiling : use (2) 6” rods and (2) 12” rods

Figure 2A

Summary of content (3 pages)

PAGE 1
Assembly Instruction Sheet #IS-BNY2822C_R1 For Style BNY2822C Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (5) A19 Medium Base 100W Maximum, Alternate bulb (5) 23W CFL Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
Assembly Instructions for Semi-flush Light (Step 1B - Step 6B) STEP 4A - Fit Ceiling Canopy to Crossbar Assembly A. Remove mounting balls from the Crossbar Assembly (A). Fit the Ceiling Canopy (F) to the Crossbar Assembly (A) and secure with mounting balls. Note: The Ceiling Canopy (F) should be snug against the ceiling and the Mounting balls.
PAGE 3
(Step 4B Continued) REPLACE INNER SHADE balls. Note: The Ceiling Canopy (F) should be snug against the wall and the mounting balls. If not, adjust the length of the nipple on Crossbar Assembly (A) by unscrewing the preassembled hex nut and lock washer and Hex Nut and then screwing mounting Lock Washer screws in or out of A Mounting crossbar until the Screw correct length is achieved. Once Ceiling F Mounting Canopy (F) is secure, Ball remove mounting ball and Ceiling Canopy (F) and proceed to Step 5B. A.