Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Baron 6 Light 20" Wide Semi-Flush Drum Ceiling Fixture

1of2

For Styles BRO2820MK and BRO1720MK

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Pleasegoto forproductcleaningtips.Gotothe selection.

(6)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.

MinimumHangingHeightis13.5”,MaximumHangingHeightis53.5”.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

www.quoizel.com Care+Maintenance

LightSource:

FixtureHangingHeight:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Note:This CONVERTIBLEfixturecanbemountedaspendantlightorsemi-flushlight.Refertorespective

installationsteps forinstallations.

Installation Guide

2019 QuoizelInc.

visit us on-line at www.quoizel.com

ReleasedDate:2019-04-04

Package Contents

Crossbar Assembly

Fixture Body

Ceiling Canopy

6” Rod

12” Rod

Assembly Instructions for Pendant Light: BRO2820MK

(Step 1A - Step 6A)

STEP 1A - Install Ceiling Canopy, Rods

and Fixture Body together

a. Determine the Rods (B/C) to be

assembled to the Fixture Body (E)

according to your hanging height.

b. Pass the supply wires and ground wire

through the chosen rods (B/C) and the

Ceiling Canopy (D). Thread the Fixture

Body (E), the chosen Rods (B/C) and the

Ceiling Canopy (D) together. Hand

tighten until snug.

Suggested rods for Ceiling height :

8’ ceiling : use (1) 6” rods and (1) 12” rods

9’ ceiling : use (1) 6” rods and (2) 12” rods

Supply Wires

and Ground Wire

Figure 1A

STEP 2A - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

STEP 3A Test Fitting Ceiling Canopy to Crossbar Assembly-

eiling Canopy to the

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

C (D) Crossbar Assembly (A) and secure with

mounting balls. Note: The should be snug

against the and the mounting balls. If

Ceiling Canopy (D)

not, adjust the length

of the nipple on the Crossbar Assembly (A) by unscrewing the

preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

achieved. Once the Ceiling Canopy (D) is secure, remove the

mounting ball and Ceiling Canopy (D) and proceed to Step 4A.

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 2A

Figure 3A

Summary of content (2 pages)

PAGE 1
Installation Guide For Styles BRO2820MK and BRO1720MK Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (6) B10 Candelabra Base bulbs 60W Maximum, bulb not included. Fixture Hanging Height: Minimum Hanging Height is 13.5”, Maximum Hanging Height is 53.5”.
PAGE 2
Assembly Instructions for Semi-Flush Light: BRO1720MK (Step 1B) STEP 4A - Wire Connections A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.