Installation Guide

1of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
February2015
Pleasegoto forproduct cleaningtips. Goto the selection.
(3)B10 CandelabraBase 60Wbulb Maximum.
www.quoizel.com Care+ Maintenance
LightSource:
ToolsRequired: Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters,wire strippers,electrical tape,safety glasses.
EstimatedAssemblyTime:
Preparation:
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
Warnings and Cautions
Assembly Instruction Sheet #IS-BRO5203MK
For Style BRO5203MK
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering June result.
D
Socket
Assembly
x1
Package Contents
A
Fixture
Loop Assembly
x1
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
STEP 2 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end of
the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place
another Lock Washer (BB) over the Nipple (DD) and then thread the
Step B
Step A
CC
BB
EE
II
FF
AA
BB
CC
DD
Figure 2
Hardware Contents
AA
BB
CC
DD
EE
FF
II
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
Canopy Lock
Ring
x1
Ceiling
Canopy
x1
GG
Fixture Chain
x1
HH
Quick Link
x2
B
Center
Stem
x1
STEP 3 Install Stem, Rod, Socket
Assembly and Fixture Loop
Assembly together
-
A. Thread Socket Assembly (D), Rod (C),
Center Stem (B) and Fixture Loop
Assembly (A) together. Hand tighten until
sung.
Nipple (DD) into the Crossbar
(AA) until the Nipple (DD) is
about 0.375” above the
Crossbar (AA).
C. Remove the Canopy Lock
Ring (FF) from the Canopy
Chain Loop (EE). Place the
Ceiling Canopy (II) over the
Canopy Chain Loop (EE)
against the ceiling to
determine the correct position
of the Nipple (DD). Thread the
Canopy Lock Ring onto the
Canopy Chain Loop (EE).
Adjust the Nipple (DD) to
allow the Ceiling Canopy (II)
to rest against the ceiling
when held in place by the
Canopy Lock Ring (FF).
D. Remove the Canopy Lock
Ring (FF) and the Ceiling
Canopy (II). Tighten the Hex
Nut (CC) against the Crossbar
(AA) to secure in place.
E
Side Arm
x3
F
Cage
x1
A
B
C
Figure 3
C
Rod
x1
D
G
Candle
Cover 3.25”L
x3