Installation Guide

Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
(6)G9XenonClearBulbs(supplied),40WMaximum
www.quoizel.com Care+Maintenance
LightSource:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
EstimatedAssemblyTime:
Preparation:
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
1of2
Assembly Instruction Sheet #IS-BRX1620C
For Style BRX1620C
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Warnings and Cautions
Crossbar Assembly
x1
B
Fixture Body
x1
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Do not touch the bulb with bare hands use a cloth or glove.
C
Wall Anchor
x4
D
Self-tapping Screw
x4
STEP 1 - Attach Inner Backplate to Outlet Box
A. Place the Crossbar Assembly (A) onto the Ceiling surface and line
up one set of holes onto mounting holes on Outlet Box. Using a
pencil, mark the locations for Wall Anchors (B).
B. Remove the Crossbar Assembly (A) and drill holes from the marks
and then push the Wall Anchors (B) into the holes.
C. Position the Crossbar Assembly (A) back onto the Ceiling. Thread
the Outlet Box Screws (not supplied) into the mounting holes on
the Outlet Box to secure it. Hand tighten until snug.
Flat Washer
x4
Mounting Ball
x4
G9 Xenon Clear Bulb
x6
Clear Crystal Drop
L: 5-7/8"
x24
Clear Crystal Drop
L: 7-1/2"
x16
Clear Crystal Drop
L: 9”
x8
E
F
G
H
I
J
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
STEP 3 - Attach Ceiling Canopy to Mounting Screw
A. Remove Protective Film from Ceiling Canopy.
Note: Gloves are required to avoid leaving fingerprints or scratches
on Ceiling Canopy.
B. Place the Ceiling Canopy on the Fixture Body (F) over the Mounting
Screws and secure with Mounting Balls (E). Hand tighten until snug.
A
STEP 4 - Install Bulb
IMPORTANT:
A. This fixture uses G9 Xenon Clear Bulbs (G). Maximum 40 watts.
Insert bulb and seat properly into place.
Do not touch the bulb with bare hands use a cloth or
glove.
Figure 4
Socket
G
CEILING
Outlet Box
B
A
C
D
Outlet Box Screw
(not included)
Figure 1
D. Pass the Flat
Washers (D) over
the Self-tapping
screws (C) and then
thread the self-
tapping screws (C)
into the Wall
Anchors (B). Hand
tighten until snug.
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Protective Film
E
F
Mounting
Screw
Figure 3
STEP 5 - Install Crystal to Fixture
A. (Refer to ) Attach Clear Crystal Drop L9-7/8” (K)
to location “D” on the center of the Ceiling Canopy. Attach Clear
Crystal Distribution
Clear Crystal Drop
L: 9-7/8”
x1
K
July2015