Installation Guide

Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
(7)G9XenonClearBulbs(supplied),40WMaximum
www.quoizel.com Care+Maintenance
LightSource:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
EstimatedAssemblyTime:
Preparation:
45-60minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
1of2
Assembly Instruction Sheet #IS-BRX1626C
For Style BRX1626C
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
March2015
Warnings and Cautions
Crossbar
x1
B
Fixture
Body
x1
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Do not touch the bulb with bare hands use a cloth or glove.
C
Wall
Anchor
x6
D
Self-tapping Screw
x6
Figure 1
STEP 1 - Attach Inner Backplate to Outlet Box
A. Place the Crossbar (A) onto the Ceiling surface and line up one set
of holes onto mounting holes on Outlet Box. Using a pencil, mark
the locations for Wall Anchors (C).
B. Remove the Crossbar (A) and drill holes from the marks and then
push the Wall Anchors (C) into the holes.
C. Position the Crossbar (A) back onto the Ceiling. Thread the Outlet
Box Screws (not supplied) into the mounting holes on the Outlet
Box to secure it. Hand tighten until snug.
D. Pass the Flat Washers (E) over the Self-tapping screws (D) and
then thread the self-tapping screws (D) into the Wall Anchors (C).
Hand tighten until snug.
E
GN
D
A
C
D
Flat Washer
x6
Mounting Ball
x4
G9 Xenon Clear Bulb
x7
Crystal 4.35"L
Part A
x21
Crystal 5.15"L
Part B
x18
Crystal 5.94”L
Part C
x12
Crystal 6.74"L
Part D
x6
Crystal 7.53”L
Part E
x1
E
F
G
H
I
J
K
L
Outlet Box
CEILING
Mounting Hole
Outlet Box Screw
(not include)
A
E
STEP 2 Attach Lanyard-
A. The purpose of the lanyard is to provide the installer a means to
support the fixture from the junction box while connecting the
electrical wires. This enables the fixture to hang from the junction
box and your hands are free to make the wire connections.
B. Turn the Button Stop so it may be inserted into the Crossbar slot.
Make sure the Button Stop is completely inside the Crossbar. Slowly
release the fixture to make sure it is supported by the Button Stop.
Proceed to the wiring steps in the next step. Once you are complete
with the wiring there is nothing to do with Lanyard. The Lanyard will
push into the junction box when the fixture is placed for final
mounting.
Button
Stop
Lanyard
Slot
A
Figure 2
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 4 - Attach Ceiling Canopy to Mounting Screw
A. Remove Protective Film from Ceiling Canopy.
Note: Gloves are required to avoid leaving fingerprints or scratches
on Ceiling Canopy.
B. Place the Ceiling Canopy on the Fixture Body (B) over the Mounting
Screws and secure with Mounting Balls (F). Hand tighten until
snug.