Installation Guide

Package Contents
1of2
Assembly Instruction Sheet #IS-BSN1714EK
For Style BSN1714EK
2016 QuoizelInc.
A
Crossbar Assembly
x1
C
Socket
Assembly
x1
ReleasedDate:2016-09-14
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
E
Cage
x1
B
Side Arm
x3
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the
Crossbar Assembly (A). Attach the
Crossbar Assembly (A) to the Outlet
Box with the head of the Green Ground
Screw facing you. Secure it with Outlet
Box Screws (not included). Tighten
until snug.
Outlet
Box
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Figure 2
A
STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
Ceiling Canopy (C) to the Crossbar Assembly (A) and secure with
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 Install Fixture-
A. Carefully tuck all wires into the
outlet box and position the
Ceiling Canopy (C) over the
outlet box. Align the holes in
the Ceiling Canopy (C) with the
mounting screws. Attach
Ceiling Canopy (C) using the
mounting balls. Hand tighten
until snug.
Mounting Ball
Mounting
Screw
C
Figure 5
A
Ceiling
Canopy
x1
D
STEP 1 Assemble Ceiling Canopy to
Socket Assembly
-
A. Thread the Ceiling Canopy (C) onto
the Socket Assembly (D) and hand
tighten until snug.
C
D
Figure 1
Mounting Ball
Hex Nut and
Lock Washer
Mounting
Screw
C
Figure 3
A
mounting balls. Note: The
Ceiling Canopy (C) should be
snug against the ceiling and the
mounting balls. If not, adjust the
length of the mounting screw on
the Crossbar Assembly (A) by
unscrewing the preassembled
hex nut and lock washer and
then screwing the mounting
screws in or out of the crossbar
until the correct length is
achieved. Once the Ceiling
Canopy (C) is secure, remove
the mounting ball and Ceiling
Canopy (C) and proceed to
Step 4.
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)B10CandelabraBasebulbs60WMaximumor
(3)CandelabraBaseT8VintageBulbsarerecommendedbutnotsupplied.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.