Installation Guide

ManualsBrandsQuoizel ManualsPost Light PartsCCR9010CU

1of2

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

2017 QuoizelInc.

Pleasegoto forproductcleaningtips.Gotothe selection.

markingpen,1/16”

drillbit,centerpunch,hammer,drillandwrench.

(3)B10CandelabraBasebulbs60WMaximum.

www.quoizel.com Care+Maintenance

LightSource:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses,

EstimatedAssemblyTime:

Preparation:

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

Assembly Instruction Sheet #IS-CCR9010CU_R1

For Style CCR9010CU

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Mounting Screw

Fixture Body

Glass

Panel

Candle

Cover

STEP 1 Remove Fixture Hood from Cage-

A. Unscrew the finial and waterproof washer, remove the fixture hood

from the Fixture Body (D).

Finial

Waterproof

Washer

Fixture Hood

Figure 1

STEP 2 Install Glass Panels-

A. Insert the Glass Panel (C) into

the cage with

. Secure by

folding the tabs in the bottom

and top edge of the cage to

the bottom and top edge of the

Glass Panel (C). Repeat for

each Glass Panel (C).

U-shaped foam

end downward

Tab

U-shaped

Foam

Figure 2

STEP 3 Install Candle Covers,

Bulbs and Fixture Hood

A. Install the Candle Cover (B) to

each socket.

B. Insert bulbs onto sockets and

screw snugly into place.

C. Place the fixture hood back

onto the top edge of the Fixture

Body (D). Secure by threading

the previously removed

waterproof washer and finial

back onto the fixture. Hand

tighten until snug.

Finial

Waterproof

Washer

Fixture Hood

Socket

Bulb (not

Supplied)

Figure 3

RevisedDate:2017-03-09

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-CCR9010CU_R1 For Style CCR9010CU 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses, marking pen, 1/16” drill bit, center punch, hammer, drill and wrench. Light Source: (3) B10 Candelabra Base bulbs 60W Maximum.
PAGE 2
STEP 4 - Mark the Location for the 3 Mounting Holes STEP 8 - Attach the fixture to the Post Mount A. Place the light fixture onto the post and mark the location of the 3 mounting holes on the fixture fitter onto the post with the marking pen. A. Place the fixture on the post lining up the mounting holes on the fixture fitter with the holes on the post. Use the Mounting Screws (A) to attach the fixture to the post. Post Lighting Fixture Fitter Your fixture is now assembled and ready to use.