Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Citadel 4 Light 14" Wide Semi-Flush Ceiling Fixture

Package Contents

Warnings and Cautions

1of2

For Style CDL1714EK

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Crossbar

Assembly

Pleasegoto forproductcleaningtips.Gotothe selection.

(4)B10CandelabraBaseBulbs60WMaximum,CandelabraBaseT8Vintage Bulbs are recommended, bulbs not included.

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Installation Guide #IS-CDL1714EK

2018 QuoizelInc.

ReleasedDate:2018-09-13

visit us on-line at www.quoizel.com

Fixture Body

Ceiling Canopy

with Nipple

Spacer Tube

STEP 1 - Install Glass Panels

(2) People are recommended for this step.

A. Remove screws and glass holder from each block at the top corner

of the Fixture Body (E).

B. Insert Glass Panels

(D) into the slot in the bottom edge of the Fixture Body (E). With one

person hold Glass Panels (D), another person place previously

removed glass holders onto the top edge of Glass Panels (D) and

align the holes on glass holders to mounting holes at the top corners

of the Fixture Body (E) as shown. Secure with previously removed

screws and hand tighten until snug with screwdrivers.

STEP 2 Install Spacer Tube and Ceiling Canopy-

A. Place the Spacer Tube (C) over the nipple at the bottom of the

Ceiling Canopy (B) and then thread the nipple onto the hex coupling

on the top center of the Fixture Body (E). Hand tighten until snug.

Figure 2

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

STEP 3 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Figure 3

STEP 4 Test Fitting Ceiling Canopy to Crossbar Assembly-

A. Remove mounting balls from the Crossbar Assembly (A). Fit the

Ceiling Canopy (B) to the Crossbar Assembly (A) and secure with

Glass Panel

Figure 1

Slot

Nipple

Hex Coupling

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Ceiling Canopy

Figure 4

Screw

Glass Holder

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-CDL1714EK For Style CDL1714EK Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (4) B10 Candelabra Base Bulbs 60W Maximum, Candelabra Base T8 Vintage Bulbs are recommended, bulbs not included.
PAGE 2
(Step 4 Continued) CDL1714EK mounting balls. Note: The Ceiling Canopy (B) should be snug against the ceiling and the mounting balls. If not, adjust the length of the nipple on the Crossbar Assembly (A) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the Ceiling Canopy (B) is secure, remove the mounting ball and Ceiling Canopy (B). FINISH: EARTH BLACK 5” SQ. STEP 5 - Wire Connections A.