Installation Guide

Hardware Contents
Package Contents
1of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
January2015
B
AA
Crossbar Assembly
x1
A
Fixture Body
x1
Stem
4.5”L
x1
against the ceiling and
the mounting balls. If
Not, adjust the length of
the nipple on the
Crossbar Assembly
(AA) by unscrewing the
preassembled hex nut
and lock washer and
then screwing the
mounting screws in or
out of the crossbar until
the correct length is
achieved. Once the
Ceiling Canopy is
secure, remove the
mounting ball and
Ceiling Canopy and
proceed to Step 3.
Mounting
Screw
Hex Nut and
Lock Washer
A
AA
Mounting Ball
Figure 2
C
Diffuser
x1
D
Flat Washer
x1
F
Hex
Nut
x1
G
Finial
x1
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the
Crossbar Assembly (AA). Attach the
Crossbar Assembly (AA) to the Outlet
Box with the head of the Green
Ground Screw facing you. Secure it
with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires
with Ground Wire
AA
Outlet Box Screws
(not included)
Outlet
Box
Figure 1
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Figure 3
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
STEP 2 Fit Ceiling Canopy to Crossbar Assembly-
A. Remove mounting balls from the Crossbar Assembly (AA). Fit the
Ceiling Canopy to the Crossbar Assembly (AA) and secure with
mounting balls. Note: The Ceiling Canopy should be snug
STEP 4 Install Fixture
Body
-
A. Carefully tuck all wires into
the outlet box and position
the Ceiling Canopy (A) over
the outlet box. Align the
holes in the Ceiling Canopy
with the mounting screws,
then attach the Ceiling
Canopy using the
previously removed
mounting balls. Hand
tighten until snug.
Mounting
Screw
AA
Mounting Ball
Ceiling
Canopy
Figure 4
Pleasegoto forproduct cleaningtips. Goto the selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters,wire strippers,electrical tape,safety glasses.
(3)A19MediumBase 100WMaximum,Alternatebulb (3)23W CFL.
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
www.quoizel.com Care+ Maintenance
ToolsRequired:
LightSource:
EstimatedAssemblyTime:
Preparation:
Assembly Instruction Sheet #IS-CKMS1716TM
For Style CKMS1716TM
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
E
Rubber Washer
x1