Installation Guide

Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
Integrated35WLED
www.quoizel.com Care+Maintenance
LightSource:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
EstimatedAssemblyTime:
Preparation:
45-60minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
1of2
Assembly Instruction Sheet #IS-CMA1405
For Styles CMA1405WT and CMA1405BN
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
CAUTION: To reduce the risk of fire, electrical shock, or personal injury, do not touch or remove the spot light on the rail when the light
is on. Instead, turn off the electrical power. Unscrew the caps and to remove the spot light from the rail. Then reinstall them back onto
the desired positions of the rail.
F
Wall
Anchor
x5
G
Self-tapping
Screw
x5
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
2016 QuoizelInc.
B
Ceiling
Canopy
x1
E
Spot Light
x5
C
Rail Support
x5
D
Rail
x1
STEP 1 Attach Crossbar to
Outlet Box
-
A. Attach the Crossbar (A) to Outlet
Box and secure by threading
Outlet Box Screws (not supplied)
into the Mounting Holes on the
Outlet Box. Tighten until snug.
A
Figure 1
Outlet
Box
Outlet Box
Screw
STEP 3 - Attach Ceiling
Canopy to Crossbar
A. Line up the holes on the
side of the Ceiling
Canopy (B) to the
mounting holes on the
Crossbar (A). Secure
them with Mounting
Screws (H). Tighten
until sung.
H
Mounting
Screw
x2
A
Crossbar
x1
H
A
B
Figure 3
STEP 4 Determine Support Position-
A. Mark two desired positions and drill them on the ceiling for two Rail
Supports (C) on the side of the Ceiling Canopy (B).
NOTE: Center the Ceiling Canopy (B) between two Rail
Supports (C) and The distance between each Rail Support (C)
and the canopy is 14 ~ 18 inches (See Fig 2-a). So the remainder
length of the rail could be bent to a wonderful arc.
Figure 4
14~15 inches
Rail
Support
Rail
Support
14~15 inches
CEILING
STEP 5 Rail support
Installation
-
A. Depart the Rail Supports
(C) as shown.
B. Insert Wall Anchors (F) into
the holes on the Ceiling.
Pass Support Base over
Self-tapping Screws (G)
and thread Self-tapping
Screws (G) into Wall
Anchors (F). Hand tighten
until snug.
C. Threading the Pipe of Rail
Supports into the Support
Bases , Tighten until snug.
Pipe of
Rail Support
Support
Base
Cap
C
CEILING
F
Support
Base
Pipe of
Rail Support
Figure 5
Figure 6
ReleaseDate:2016-03-30