Installation Guide

ManualsBrandsQuoizel ManualsOutdoor Pendant LightsCPT1910PN

1of3

Assembly Instruction Sheet #IS-CPT1910PN

For Style CPT1910PN

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Package Contents

Hardware Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Canopy

Chain Loop

Canopy Lock

Ring

Ceiling

Canopy

Fixture Chain

Quick Link

Pleasegoto forproductcleaningtips.Gotothe selection.

(1)A21MediumBaseBulb150WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

2017 QuoizelInc.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

Fixture Body

ReleasedDate:2017-04-21

Figure 1

STEP 1 Remove Styrofoam

inside of the Cage

A. Unscrew lock screws on the

fixture hood by using screwdrivers

and remove the cage from the

fixture body.

B. Carefully remove the Styrofoam

inside of the cage.

C. Place the cage back onto the

fixture body and secure with

previously removed lock screws.

Tighten until snug with

screwdrivers.

Lock

Screw

Styrofoam

Cage

Fixture Body

STEP 3 Install the Canopy Chain Loop and Nipple-

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end of

the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the

Nipple (DD). By using pliers, thread the Hex Nut (CC) against the

Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place

another Lock Washer (BB) over the Nipple (DD) and then thread the

Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about

0.375” above the Crossbar (AA).

C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop

(EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop

(EE) against the ceiling to determine the correct position of the

Step B

Step A

Figure 3

Nipple (DD). Thread the

Canopy Lock Ring onto

the Canopy Chain Loop

(EE). Adjust the Nipple

(DD) to allow the Ceiling

Canopy (II) to rest against

the ceiling when held in

place by the Canopy Lock

Ring (FF).

D. Remove the Canopy Lock

Ring (FF) and the Ceiling

Canopy (II). Tighten the

Hex Nut (CC) against the

Crossbar (AA) to secure

in place.

STEP 2 Install the Crossbar to the junction box-

A. Attach the Crossbar (AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included), tighten until snug

Figure 2

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

Summary of content (3 pages)

PAGE 1
Assembly Instruction Sheet #IS-CPT1910PN For Style CPT1910PN 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
PAGE 2
STEP 4 - Install the Fixture Chain and Ceiling Canopy STEP 6 - Install the Bulb A. Adjust the Fixture Chain (GG) to your desired length by removing links if needed. B. Pull the supply wires through the Fixture Chain (GG) alternating links. After the wires are through the Fixture Chain (GG), pull the Supply Wires and the Ground Wire through the Canopy Lock Ring (FF) and the Ceiling Canopy (II) in order. C. Attach one end of the Fixture Chain (GG) to the Fixture Loop with one Quick Link (HH).
PAGE 3
CPT1910PN NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" FINISH: PALLADIAN BRONZE 5” SQ. 118.5” OVERALL HEIGHT ( INCLUDES 96” CHAIN AND 2 QUICK LINKS ) 16” 9.75" 9.75" 2017 QuoizelInc. Thank you for purchasing a Quoizel product. Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.