Installation Guide

1of3
Assembly Instruction Sheet #IS-CS1718RK
For Style CS1718RK
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
January2015
Package Contents
Hardware Contents
Ceiling
Canopy
x1
Fixture Chain
x1
HH
Quick Link
x2
II
JJ
Mounting Screw
x2
KK
Small Lock Washer
x2
Small Hex Nut
x2
STEP 1 Install Crossbar-
A. A)Attach the Crossbar (A to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
FOR HANGING
AA
Crossbar
x1
AA
BB
CC
DD
EE
Lock Washer
x2
Big Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
FF
Canopy Lock
Ring
x1
GG
LL
Pleasegoto forproduct cleaningtips. Goto the selection.www.quoizel.com Care+ Maintenance
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape, safetyglasses.
EstimatedAssemblyTime:30-45 minutes
Preparation:
Note:This fixturecan bemounted ashanging orsemi-flush. Referto respectiveinstallation stepsfor installations.
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
LightSource: (4)B10 CandelabraBase 60Wbulb Maximum.
C
Socket
Assembly
x1
A
Fixture
Loop
x1
B
Center
Column
x1
D
Nipple
x1
F
Finial
x1
E
Cap
x1
STEP 2 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end of
the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place
another Lock Washer (BB) over the Nipple (DD) and then thread the
Step B
Step A
CC
BB
EE
II
FF
AA
BB
CC
DD
Figure 2
STEP 3 Install Column to Fixture
Body
-
A. Unfold support arms on fixture
assembly to proper locations.
B. Thread Center Column (B) onto Socket
Assembly (C), tighten until sung.
C. Thread Fixture Loop (A) onto the
nipple on the top of Center Column (B),
hand tighten until sung.
Nipple (DD) into the Crossbar
(AA) until the Nipple (DD) is
about 0.375” above the
Crossbar (AA).
C. Remove the Canopy Lock Ring
(FF) from the Canopy Chain
Loop (EE). Place the Ceiling
Canopy (II) over the Canopy
Chain Loop (EE) against the
ceiling to determine the correct
position of the Nipple (DD).
Thread the Canopy Lock Ring
onto the Canopy Chain Loop
(EE). Adjust the Nipple (DD) to
allow the Ceiling Canopy (II) to
rest against the ceiling when
held in place by the Canopy
Lock Ring (FF).
D. Remove the Canopy Lock Ring
(FF) and the Ceiling Canopy
(II). Tighten the Hex Nut (CC)
against the Crossbar (AA) to
secure in place.
Figure 3
A
B
C