Installation Guide

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2017 QuoizelInc.
Assembly Instruction Sheet #IS-DBN1707PN
For Style DBN1707PN
ReleasedDate:2017-03-27
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBaseBulb100WMaximum.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
A
Crossbar
Assembly
x1
B
Lock Screw
x3
C
Fixture
Body
x1
D
Shade
x1
STEP 1 - Installing the Crossbar
Assembly
A. Pass the supply wires through the
Crossbar Assembly (A). Attach the
Crossbar Assembly (A) to the Outlet
Box with the head of the Green
Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet
Box Screws (not included). Tighten
until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 1
STEP 2 - Test Fit the Ceiling Canopy to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the ceiling canopy and Fixture Body (C) onto the Crossbar Assembly
(A) and secure with mounting balls. Note: The ceiling canopy and
Fixture Body (C) should be snug against the ceiling and held tight
with the mounting balls. If it is not, adjust the length of the mounting
screws on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
Mounting
Screw
Hex Nut and
Lock Washer
Mounting
Ball
A
C
Figure 2
achieved. Once the
ceiling canopy and
Fixture Body (C) is
secure, remove the
mounting ball and
Fixture Body (C) and
proceed to Step 3.
Ceiling
Canopy
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Bare, or Green
Ground wire
from outlet box
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar
Figure 3
STEP 4 Install the Fixture
Body
-
A. Position the ceiling canopy
and Fixture Body (C) onto
the Crossbar Assembly (A).
Place the holes in the ceiling
canopy over the mounting
screws. Secure the Fixture
Body by using the mounting
balls and hand tighten the
mounting balls until snug.
Figure 4
STEP 5 Install Bulb and Shade-
A. Install bulb onto socket and screw
snugly into place.
B. Place the Shade (D) over the bulb
and attach the Shade (D) onto the
Fixture Body (C). Thread Lock
Screws (B) onto the Fixture Body (C)
and attach Lock Screws (B) onto the
bottom of the Shade lips. Carefully
release your hands after (3) Lock
Screws are screwed in place.
Your fixture is now assembled and
ready to use. Enjoy!
Bulb (not
supplied)
C
Figure 5
Mounting
Screw
Mounting
Ball
A
C
Ceiling
Canopy
D
B
Socket