Installation Guide

()2 MOUNTING SCREWS
CROSSBAR
GREEN GROUND SCREW
()
()
2 OUTLET BOX SCREWS
not supplied
SUPPLY WIRE
and GROUND WIRE
()2 MOUNTING BALLS
FIGURE2
OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied()
GREEN GROUND SCREW
CROSSBAR
SHAKE PROOF WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
SHAKE PROOF WASHER B
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN
CEILING CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
FIGURE 1
FIXTURE CANOPY
SOCKET
CLUSTER
NIPPLE ASSEMBLY
PLANE WASHER
PLANE WASHER
SHADE
PLASTIC WASHER
HEX NUT
CAP
KNOB
FIXTURE LOOP
() ()2 PAN HEAD S
FIXTURE CANOPY
ASSEMBLY / INSTALLATION INSTRUCTIONS:
1.Before beginning the installation, carefully unpack and identify all parts, referring to the illustration
(FIGURE 2).
2. Turn the power to the installation point OFF at circuit breaker.
3.Unfold ARMS to proper location Thread the top end of NIPPLE ASSEMBLY into coupling on the
bottom center of SOCKET CLUSTER Hand tighten until snug Locate the following components
in this order PLANE WASHER PLASTIC WASHER SHADE PLASTIC WASHER PLANE WASHER
Secure them together by threading HEX NUT onto end of NIPPLE ASSEMBLY Hand tighten until
snug roceed to locate CAP over end of NIPPLE ASSEMBLY and thread KNOB onto the nipple
until snug to secure it
4.Determine the hanging method [chain or direct].
(see FIGURE 1)
a. Fasten the CROSSBAR to the OUTLET BOX with (2) OUTLET BOX SCREWS (not supplied). Proceed
to thread LOCK NUT A and SHAKE PROOF WASHER A onto the top end of NIPPLE. Thread NIPPLE
into the center of CROSSBAR. Locate the LOCK NUT B onto the bottom end of the NIPPLE. Tighten
LOCK NUT A against CROSSBAR with plier until snug.
b. Locate the FIXTURE LOOP and pass wires through the center. Take up wire slack and thread end of
FIXTURE LOOP onto the nipple on the top center of the FIXTURE CANOPY, tighten until snug.
c Locate the FIXTURE CHAIN and determine desired hanging height of fixture. Adjust chain by
removing links if needed. Please note that depending on chain material thickness, you might be
required to use chain pliers to spread links open. Proceed to attach one end of chain to FIXTURE
LOOP, attached to top of fixture. Pass the fixture wires through FIXTURE CHAIN alternating links.
Proceed to pass the fixture wires through the following mounting components in this order: 1) CANOPY
LOCK RING; 2) CEILING CANOPY; 3) CANOPY CHAIN LOOP 4) SHAKE PROOF WASHER B.
d. Locate the (2) MOUNTING BALLS and attach them to the FIXTURE CANOPY with (2) PAN HEAD
screws. These are used to hide the MOUNTING HOLES used in the DIRECT MOUNTING application.
e. Making the wire connectors 2 people recommended for this step : Using wire connectors not
supplied connect the HOUSE GROUND WIRE to the FIXTURE GROUND WIRE connect the
HOUSE WHITE WIRE to the FIXTURE WHITE (or RIBBED) LEAD; connect the HOUSE BLACK (or RED)
WIRE to the FIXTURE (or SMOOTH) LEAD. Wrap each connection with approved electrical tape
f. Carefully tuck all wiring up into the OUTLET BOX. Thread the CANOPY CHAIN LOOP onto the
NIPPLE. Locate the CEILING CANOPY over OUTLET BOX and secure by threading the LOCK RING
onto the CANOPY CHIAN LOOP.
;
.
..
:, ,, ,.
.
.
.
.
()(
) ;
.
P
Chain-Hung Mounting:
Direct Mounting:
(see FIGURE 2)
a. Locate the (2)MOUTNING SCREWS and thread them into the back of the CROSSBAR, making sure that they match the
holes in the FIXTURE CANOPY. Using (2) OUTLET BOX SCREWS (not included), fasten the CROSSBAR to the OUTLET
BOX.
b. : Using wire connectors not supplied connect
the HOUSE GROUND WIRE to the FIXTURE GROUND WIRE connect the HOUSE WHITE WIRE to the FIXTURE
WHITE (or RIBBED)LEAD; connect the HOUSE BLACK (or RED) WIRE to the FIXTURE (or SMOOTH) LEAD. Wrap each
connection with approved electrical tape
c. Carefully tuck all of the wiring up into the outlet box, and fit the FIXTURE CANOPY over the MOUNTING SCREWS.
Secure the FIXTURE CANOPY to the ceiling with the (2)MOUNTING BALLS, making sure that the balls are fully threaded
onto the MOUNTING SCREWS before tightening.
5.Install bulbs referring to fixture markings and or labels for maximum wattage
6. Return power to the installation point ON. Retain this sheet for future reference.
()()
;
.
Making the wire connectors 2 people recommended for this step
/.
IS DH1718
12 05
-
.
ARM
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..