Installation Guide

Xenon or if you purchased the
LED model it is supplied with G9
LED bulbs.
Your fixture is now assembled
and ready to use. Enjoy!
Package Contents
Warnings and Cautions
1of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
B
Lock
Screw
x4
Inner
Backplate
x1
STEP 1 Install Inner Backplate and
Fixture Body
-
A. Pass the supply wires through Inner
Backplate (A). Attach Inner Backplate
(A) to Outlet Box with the head of
Green Ground Screw facing you.
Secure it with Outlet Box Screws (not
included). Tighten until snug
B. Race all supply wires through the Inner
Backplate (A) as shown. Refer to Step
2 for wiring connections.
C. Attach Fixture Body (D) over Inner
Backplate (A) and secure with Lock
Screws (B). Tighten until snug with
screwdrivers.
.
A
D
Fixture Body
x1
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires between Inner Backplate (A) and Fixture Body (D).
A
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
Figure 1
Outlet
Box
Outlet Box
Screw
D
B
STEP 3 - Install Shades, Bulbs and Bulb Shields
A. Place Shade (E) and Steel Collar (G) over Socket as shown. Secure
by threading Socket Collar (F) onto socket. Hand tighten until snug.
B. Install either the G9 Xenon bulb as specified (not provided) or install
C
F
E
Socket
the G9 LED bulbs (provided) if the fixture
purchased is the LED model.
This fixture is rated to use 60W maximum
G9 Xenon bulbs. You may use a lower wattage G9
Note:
Figure 3
E
Shade
x2
F
Socket Collar
x2
C
CAUTION FOR BULB REPLACING
When replacing bulbs, turn off power and allow lamp to cool. For safety purpose, wear gloves and eye protection.
Assembly Instruction Sheet #IS-DVN8602
For Styles DVN8602C, DVN8602BN, DVN8602CLED and DVN8602BNLED
Pleasegoto forproduct cleaningtips. Goto the selection.
(2)LED G94.5W Bulbs,Maximum 60WG9 XenonFrosted Bulbs
Ifthe styleyou purchasedis DVN8602Cor DVN8602BNit isNOT providedwith lightbulbs. Ifthe styleyou purchasedisDVN8602CLEDor
DVN8602BNLEDit isprovided with(2) G9LED lightbulbs. TheG9 LEDbulb isan energyefficientbulb andwill reducethe useof electricityin
comparisonto G9Xenon bulbs,saving youmoney. Please goto Quoizel.comto seethe G9LED bulbspecifications providedwith yourfixture.
www.quoizel.com Care+ Maintenance
Note:
Tools Required:Flathead screwdriver, Phillipsscrewdriver,pliers,wire cutters,wire strippers,electrical tape,safety glasses.
BulbRecommended:
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
LEDG9Bulb x2
Included with DVN8602CLED
and DVN8602BNLED models only.
December2015
Rev.B
G
Steel Collar
x2
G