Installation Guide

1of1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
September2014
Package Contents
STEP 2 Drill Pilot Holes on Post-
A. Carefully fit the Post Fitter over the
end of the Post (not supplied),
making sure the Post Fitter is fully
seated.
B. Mark the drill point for the (3)
Mounting Screws, using (3)
Mounting Holes as reference. After
marking hole locations, remove
fixture from post and drill 1/16” pilot
holes for screws.
Post
Post Fitter
Figure 2
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers,wire cutters,wire strippers,electrical tape,safety glasses.
BulbRecommended: (3) CandelabraBase Bulbs60W Maximum
EstimatedAssemblyTime:
Preparation:
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besureall partsare
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperatethefixture.Contact customerservice forreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 4 Attach Fixture Body to Post-
A. Coat the top 1” of the Post with Clear
Silicone Caulk (not supplied) and
position the Post Fitter onto the Post. Be
sure to seat it completely, aligning the
holes in the Fitter with the 1/16” Pilot
Holes drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws (A).
Your fixture is now assembled and
ready to use. Enjoy!
A
Mounting Screw
x3
B
Fixture Body
x1
STEP 1 Install Bulb-
A. Remove Fixture Hood from the top
of the Cage by unscrewing Lock
Screws.
B. This fixture uses candelabra bulbs
with standard screw base.
Maximum 60 watts. Insert bulb and
screw snugly into place.
C. Place Fixture Hood back onto the
top edge of the Cage and secure
with Lock Screws. Hand tighten
until snug.
Bulb
Socket
Figure 1
Assembly Instruction Sheet #IS-FQ9011
For Styles FQ9011AW and FQ9011MK
Mounting Hole
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Post
Post Fitter
Figure 4
Mounting Hole
FQ9011AW/FQ9011MK
(3) 60W Candelabra
Bulbs
(Not Supplied)
Base
PART NUMBER REPLACEMENT PART
REQ.
NO.
1 G4029A GLASS PANEL 4
NOTE: ALL DIMENSIONS ARE
ROUNDED UP TO THE NEAREST 1/2"
11” SQ.
19”
1
FINISH: ANTIQUE BROWN/
MARCADO BLACK
A
Cage
Fixture
Hood
Lock
Screw