Installation Sheet

ManualsBrandsQuoizel Manualspost lightsQuoizel Guardsman 3 Light 21-3/4" Tall Outdoor Single Head Post Light with Seedy Glass Panels

1of2

Pleasegoto forproductcleaningtips.Gotothe selection.

markingpen,1/16”

drillbit,centerpunch,hammer,drillandwrench.

(3)B10CandelabraBasebulbs60WMaximum,bulbsnotincluded.

www.quoizel.com Care+Maintenance

LightSource:

ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses,

EstimatedAssemblyTime:

Preparation:

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof

purchase.

For Style GDM9008PN

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Mounting Screw

Fixture

Body

Figure 2

Handle

STEP 1 Install Bulbs-

A. Unscrew lock screws on the

bottom edge of the cage and

remove the cage from the

Fixture Body (C).

B. Remove Styrofoam inside of

the cage.

C. Insert bulbs onto sockets and

screw snugly into place.

D. Place the cage back onto the

Fixture Body (C) and secure

with previously removed lock

screws. Hand tighten until

snug.

STEP 2 Install Handle-

A. Remove lock screws from the

Fixture Body (C).

B. Attach the Handle (B) to the

Fixture Body (C) and secure by

threading lock screws back into

mounting holes on the Fixture

Body (C). Hand tighten until

snug.

Lock Screw

Bulb (not

included)

Cage

Figure 1

Mounting

Hole

STEP 3 - Mark the Location for the 3 Mounting Holes

A. Place the light fixture onto the post and mark the location of the 3

mounting holes on the fixture fitter onto the post with the marking

pen.

Fixture

Fitter

Marking Pen

Mounting Hole

Post

Lighting

Post

Fixture

Fitter

Figure 3

Styrofoam

(Remove)

2018 QuoizelInc.

ReleasedDate:2018-04-04

visit us on-line at www.quoizel.com

Installation Guide #IS-GDM9008PN

Lock

Screw

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-GDM9008PN For Style GDM9008PN Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses, marking pen, 1/16” drill bit, center punch, hammer, drill and wrench. Light Source: (3) B10 Candelabra Base bulbs 60W Maximum, bulbs not included.
PAGE 2
STEP 4 - M arking the C enter of E ach M ounting H ole HOW TO REPLACE GLASS PANEL A. Remove the light fixture. Using the center punch and hammer marking the center of each mounting hole location that is marked with the marking pen. A. Unscrew screws on the bottom corners of the Fixture Body to remove the cage from the Fixture Body. B. Unscrew screws on the bottom corners of the cage and remove blocks and the glass panel holder from the cage. C. Replace glass panel carefully.