Installation Guide

ManualsBrandsQuoizel ManualsFlush Mount LightsGF1617AN

1of2

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2015 QuoizelInc.

Pleasegoto forproduct cleaningtips. Goto the selection.www.quoizel.com Care+ Maintenance

ToolsRequired: Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters,wire strippers,electrical tape,safety glasses.

LightSource: (3)Medium Base100W Maximum,Alternatebulb (3)23W CFL

EstimatedAssemblyTime:

Preparation:

30-45minutes

Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are

present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement

parts.

Warnings and Cautions

Assembly Instruction Sheet #IS-GF1617

For Styles GF1617AN, GF1617PN, GF1617 and GF1617WSC

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

February2015

Hardware Contents

Crossbar Assembly

STEP 1 Install Crossbar Assembly-

A. Pass the supply wires through the Crossbar Assembly (AA). Attach

the Crossbar Assembly (AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included). Tighten until snug

Figure 1

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

STEP 2 Fit Ceiling Canopy to Crossbar Assembly-

A. Remove mounting balls from the Crossbar Assembly (AA). Fit the

ceiling canopy of the Fixture Body (A) to the Crossbar Assembly (AA)

and secure with mounting balls. Note: The Ceiling Canopy should be

snug against the ceiling and the mounting balls. If not, adjust the

length of the nipple on the Crossbar Assembly (AA) by unscrewing

the preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

achieved. Once the Ceiling Canopy is secure, remove the mounting

ball and Ceiling Canopy and proceed to Step 3.

Ceiling

Canopy

Hex Nut and

Lock Washer

Mounting

Screw

Mounting

Ball

Figure 2

STEP 3 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Twist

connectors until wires are tightly joined together. Wrap each

connection with approved electrical tape and carefully stuff all the

connected wires into the Outlet Box.

White wire

from supply

White wire

from fixture

Black wire from

supply (or Red)

Black wire

from fixture

Ground wire

from supply

Ground wire

from fixture

Figure 3

STEP 4 Install Fixture Body-

A. Carefully tuck all wires into the outlet box and position the Ceiling

Canopy on the Fixture Body (A) over the outlet box. Align the holes

in the Ceiling Canopy with the mounting screws, then attach the

Ceiling Canopy using the previously removed mounting balls. Hand

tighten until snug.

Package Contents

Fixture

Body

Check

Ring

Center

Stem

Big Rubber

Washer

Big Flat

Washer

Spacer

Tube

Shade

Hex Nut

Cap

Finial

Small Flat

Washer

Small

Rubber

Washer

Ceiling

Canopy

Mounting

Screw

Mounting

Ball

Figure 4

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-GF1617 For Styles GF1617AN, GF1617PN, GF1617C and GF1617WS Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) Medium Base 100W Maximum, Alternate bulb (3) 23W CFL Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
STEP 5 - Install Shade STEP 6 - Install Cap A. Place one Check Ring (B) over the beaded end of the Center Stem (C). And then thread the beaded end of the Center Stem (C) into the Hex Coupling underside of the Fixture Body (A). Hand tighten until snug. B. Place the following components over the end of the Center Stem (C) as shown: Spacer Tube (D), Check Ring (B), Big Flat Washers (E), Big Rubber Washers (F),Small Flat Washers (G), Small Rubber Washers (H) and Shade (I).