Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.
(6)B10CandelabraBaseBulbs60WMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
1of3
Assembly Instruction Sheet #IS-GLY648BA
For Style GLY648BA
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Hardware Contents
AA
BB
CC
DD
Crossbar
x1
Lock Washer
x1
Hex Nut
x3
Nipple
x1
GG
Quick Link
x4
Ceiling Canopy
x1
ReleasedDate:2016-11-10
B
Fixture Body
x1
EE
A
Fixture
Loop
x2
STEP 2 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Figure 2
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
STEP 3 Install Nipple to Crossbar-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the
Lock Washer (BB) over the Nipple (DD) and then thread the Nipple
(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375”
above the Crossbar (AA).
B. Place the Ceiling Canopy (HH) over the Nipple (DD) against the
ceiling to determine the correct position of the Nipple (DD). Thread
the Lock Ball (FF) onto the Nipple (DD). Adjust the Nipple (DD) to
allow the Ceiling Canopy (HH) to rest against the ceiling when held
in place by the Lock Ball (FF).
C. Remove the Ceiling Canopy (HH) and then tighten the Hex Nut (CC)
against the Crossbar (AA) to secure in place.
AA
BB
CC
DD
Step A
Figure 3
CC
D. Thread another Hex Nut
(CC) onto the end of the
Nipple (DD). Thread this Hex
Nut (CC) on just enough so
the inside surface of the
Ceiling Canopy (HH) rests
against it. * You may have to
trial fit the Ceiling Canopy
(HH) one more times to
insure this distance also.
This Hex Nut (CC) is needed
here to prevent you from
crushing down the center of
the Ceiling Canopy (HH).
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
FF
Lock Nut
x1
HH
Fixture Chain
x2
STEP 1 Assemble Fixture Loop to Fixture Body-
A. Thread the Fixture Loop (A) onto the top of the Fixture Body (B).
Hand tighten until snug. Make sure (2) Fixture Loops (A) are in the
same direction after tighten.
A
B
Figure 1
FF
STEP 4 - Install Fixture Chain
A. Adjust the Fixture Chain (GG) to your desired length by removing
links if needed.
Pliers is required for this step.
B. With the Fixture Chains (GG) not attached to the Fixture Loops on
the top of the Fixture Body (B) and on the bottom of the Ceiling
Canopy (HH), pull the supply wires and ground wire through one of
the Fixture Chain (GG) alternating links. After the supply wires and
ground wire are through the Fixture Chain (GG), pull the Supply
*
HH
C
Optional
Candle Cover
x6