Installation Guide

OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied()
CROSSBAR
LOCK WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
LOCK WASHER B
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN
CEILING CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE LOOP
FIXTURE HOOD
SOCKET BASE
LAMP
LOCK SCREW
TAB
GLASS PANEL
LOCK
SCREW
CAGE
1 Before beginning the installation carefully unpack
and identify all parts referring to the illustration
2 Turn power to the installation point OFF at circuit
breaker
3 Slip down the GLASS PANELS inside of the CAGE
Place the TABS onto the top edge of the GLASS
PANELS and match the holes with the mounting
holes on the top edge of the CAGE Secure by
threading the LOCK SCREWS into the mounting
holes and hand tighten until snug
4 Install the Lamp into the Socket Base by aligning the
pins on the Lamp with the keyholes in the Socket Base.
Once they are aligned, gently push the Lamp into the
keyholes and twist the Lamp to lock it in place
5 Assemble the FIXTURE HOOD and the CAGE
together Match the holes on the top edge of the
CAGE with the mounting holes on the bottom of the
FIXTURE HOOD Secure them together by threading
the LOCK SCREWS into the mounting holes and
tighten until snug
6 Thread the FIXTURE LOOP onto the nipple on the
top center of the FIXTURE HOOD Hand tighten
until snug
7 Fasten the CROSSBAR to the OUTLET BOX with
(2)OUTLET BOX SCREWS(not supplied). Proceed to
thread LOCK NUT A and LOCK WASHER A onto
the top end of NIPPLE. Thread NIPPLE into the center
of CROSSBAR. Locate the LOCK NUT B onto the
bottom end of the NIPPLE. Tighten LOCK NUT A
against CROSSBAR with plier until snug.
8. Locate the FIXTURE CHAIN and determine desired
hanging height of fixture.Adjust chain by removing
links if needed. Please note that depending on chain
material thickness, you might be required to use chain
pliers to spread links open. Proceed to attach one end
of chain to FIXTURE LOOP, attached to top of fixture.
Pass the fixture wires through FIXTURE CHAIN
alternating links. Proceed to pass the fixture wires
through the following mounting components in this
order: 1)CANOPY LOCK RING; 2)CEILING
CANOPY 3 CANOPY CHAIN LOOP 4 LOCK
WASHER B and LOCK NUT B 5 NIPPLE 6 LOCK
NUT A and LOCK WASHER A
9.
(2 people recommended for the remaining steps)
Position the fixture under the ceiling mounted outlet
box. Pass LOCK WASHER B over the NIPPLE.
Thread CANOPY CHAIN LOOP onto NIPPLE. Thread
LOCK NUT B down the NIPPLE, against the CANOPY
CHAIN LOOP and snug with pliers. Pass the wires
through the NIPPLE. Take up wire slack and trim wires
so that approx. 6” will remain inside outlet box.
Proceed to attach the top of the FIXTURE CHAIN to
the bottom of the CANOPY CHAIN LOOP.
Using wire connectors (not supplied) connect the
HOUSE GROUND WIRE to the FIXTURE GROUND
WIRE connect the HOUSE WHITE WIRE to the
FIXTURE SUPPLYWIRE (WHITE or RIBBED SIDE);
connect the HOUSE BLACK (or RED) WIRE to the
FIXTURE SUPPLY WIRE(BLACK or SMOOTH SIDE).
Wrap each connection with approved electrical tape.
10. With the proper connections made, proceed to push
the CEILING CANOPY upward over the OUTLET BOX
Be sure that all wires are carefully tucked into the
OUTLET BOX cavity. Secure canopy against ceiling
by threading CANOPY LOCK RING onto the CANOPY
LOOP. Tighten until snug.
11 Restore power to the installation point ON. Retain
this sheet for future reference.
.
.
.
.
.
,
,.
..
.
.
.
.
.
.
.
.
.
.
;) ;)
;) ; )
.
;
.
.
Making the connections:
ASSEMBLY / INSTALLATION INSTRUCTIONS
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
IS-HC1909FL
2007 10 20
--